Difference between revisions of "Atftp server"
(→Bugs) |
Unnilennium (talk | contribs) |
||
| (10 intermediate revisions by 6 users not shown) | |||
| Line 1: | Line 1: | ||
| − | == | + | {{Languages}} |
| − | + | {{Request for deletion}} | |
| + | {{Ready for deletion}} | ||
| + | |||
| + | ===Maintainer=== | ||
| + | [mailto:smeserver@batley.id.au Trevor Batley]<br> | ||
Current vesrion: 1.0-1<br> | Current vesrion: 1.0-1<br> | ||
| − | |||
=== Description === | === Description === | ||
| Line 16: | Line 19: | ||
=== Installation === | === Installation === | ||
| − | This contrib is currently held in the smedev repository (I will try to move it into | + | This contrib is currently held in the smedev repository (I will try to move it into smecontribs), so the following commands will install on your smeserver. atftp-server is currently available in the [[#dag Repository | dag repository]].<br /> |
| − | yum --enablerepo=smedev --enablerepo | + | You need to activate the [[Dag]] reposity before installing this contrib.<br /> |
| + | |||
| + | see [[dag|dag repository]] <br /> | ||
| + | |||
| + | yum --enablerepo=smedev --enablerepo=dag install smeserver-atftp-server | ||
Officially you should then need to activate the database changes etc., but this is not required for this package. | Officially you should then need to activate the database changes etc., but this is not required for this package. | ||
| Line 96: | Line 103: | ||
Please raise bugs under the SME-Contribs section in {{BugzillaFileBug|product=|component=|title=bugzilla}}and select the smeserver-atftp-server component or use {{BugzillaFileBug|product=SME%20Contribs|component=smeserver-atftp-server|title=this link}}. | Please raise bugs under the SME-Contribs section in {{BugzillaFileBug|product=|component=|title=bugzilla}}and select the smeserver-atftp-server component or use {{BugzillaFileBug|product=SME%20Contribs|component=smeserver-atftp-server|title=this link}}. | ||
=== dag Repository === | === dag Repository === | ||
| − | + | You need to activate the [[Dag]] reposity before installing this contrib.<br /> | |
| + | |||
| + | see [[dag|dag repository]] <br /> | ||
| + | |||
---- | ---- | ||
| − | [[Category: Contrib]] | + | [[Category: Deprecated Contrib]] |
| + | [[Category: Administration]] | ||
Latest revision as of 05:55, 18 April 2021
Maintainer
Trevor Batley
Current vesrion: 1.0-1
Description
This contribution adds a tftp server (atftp-server) to your smeserver (primarily used by workstations that are using the pxeboot protocol to retrieve boot images and parameters from the server).
It was produced to support my smeserver-thinclient contrib, but can be used independently.
I also have a sister contrib that uses tftp-server, if you prefer that server. It works the same as this one and is interchangeable.
Requires
- smeserver >= 7.0
- atftp-server >= 0.7-3
Installation
This contrib is currently held in the smedev repository (I will try to move it into smecontribs), so the following commands will install on your smeserver. atftp-server is currently available in the dag repository.
You need to activate the Dag reposity before installing this contrib.
see dag repository
yum --enablerepo=smedev --enablerepo=dag install smeserver-atftp-server
Officially you should then need to activate the database changes etc., but this is not required for this package.
signal-event post-upgrade signal-event reboot
The tftpd status is controlled via the Thin Clients server-manager panel if you have installed my smeserver-thinclient contrib.
If you haven't, you'll need to enable the atftp server and expand all the templates etc.
config setprop tftpd status enabled signal-event tftpd-conf
If for any reason the atftp server isn't running, try:
/etc/init.d/supervise/tftpd restart
Defaults
You shouldn't need to play with any parameters (except status). The defaults and allowed values are listed below.
| <prop> | default <value> | allowed Values | description |
|---|---|---|---|
| status | disabled | enabled/disabled | |
| access | private | private/public/localhost | private = internal interface ONLY
public = all interfaces localhost = localhost ONLY disabled = none |
| user | root | root/nobody | should default to nobody, but this doesn't work |
| timeout | default | default/300 | default = 900 seconds (15 minutes) |
| UDPPort | 69 | any port | |
| directory | /tftpboot | any directory |
These settings can be set/changed via
config setprop tftpd <prop> <value> signal-event tftpd-conf
Uninstall
yum remove smeserver-atftp-server atftp-server
Everything should be turned off, but if not, or you just want to make sure
/etc/init.d/supervise/tftpd stop
An error saying that /etc/init.d/supervise/tftpd does not exist should be returned
Source
The source for this contrib can be found in the smeserver CVS on sourceforge.
Bugs
Please raise bugs under the SME-Contribs section in bugzilla and select the smeserver-atftp-server component or use this link .
dag Repository
You need to activate the Dag reposity before installing this contrib.
see dag repository
