Testing Environments

Languages:

English  • français

Helpful Wiki Pages

• Development Dashboard

• QA Verifications

• Koozali SME 10 QA

• Extra Repositories that may be needed for test scenarios

• Simple Package Modification
• Setting_up_RPM_Building_for_SME_Server

Hardware

Hardware Compatability

For testing purposes hardware compatibility is a particularly important concern if you have an older or custom-built system. Because hardware specifications change almost daily, it is recommended that systems should be checked for compatibility. The most recent list of supported hardware can be found in the Red Hat Hardware Compatibility List, available online at https://access.redhat.com/ecosystem/search/#/category/Server. Also see Red Hat Enterprise Linux technology capabilities and limits for general information about system requirements.

As a general rule just about any hardware will suffice as a Standalone test machines or as a host for a virtual environment.

Install ISO for Testing or Bug Verification

Its simple for those who do this regularly, it can be a bloody mine pit for someone who doesn't 🙂 very easy to kill a test system and no way to get out but wipe and start again, please don't be put off, if nothing else it sure educates you on the blackmagic in koozali/sme

1. Install current iso that is available from the Koozali webssite - Downloads

	Warning:
	Be aware you should never perform a full yum update with the /smetest and/or /smedev repos enabled it will almost certainly put your server in a state that may not be recoverable from..

2. Once installed, use SSH, SSH access must be enabled with the /server-manager, set remote access to allow, from the cli run a # yum update (DO NOT enable any repos) there can be many mb of updates depending on age of iso, on occasion ie very very rarely smeserver-yum may also need updating first, it may be in smeupdates-testing or updates, so a heads up a quick look under the hood can save a world of grief, Koozali Repository eg

# yum update smeserver-yum --enablerepo=smeupdates-testing

3. Make sure to reboot/reconfig

# signal-event post-upgrade; signal-event reboot

4. Best practice is to select a Bug that need verifying, See the Dashboard in the wiki, update the package with the uopdated rpm listed in the Bug

# yum update e-smith-base --enablerepo=smeupdates-testing (ONLY this)

5. Now for the fly in the ointment - sometimes, rarely, there will be a package in /smetest that fixes a borked update in smeupdates-testing, that situation can arise with any update, these will appear in smeupdates-testing eventually, it is alwways a good idea to check in /smetest for a later version of a package.

6. If you issue the following

# yum update --enablerepo=smeupdates-testing 

you will update ALL the packages that have been updated or added and need testing, every new/modified rpm - a danger Will Robinson moment if there ever was one - this not recommended but can be useful to carry out overall testing of the system or Contrib updates/import testing and verification BUT beware you could also kill your test box VM 🙂

Have fun..always learning

VM Setups

VirtualBox

Content to be done

Microsoft Windows

Content to be done

MacOS

Very remiss of me (Terry Fage) in not mentioning the MacOS setup was captured and written up by Chris (I wont list his username unless he wants to) I simply copied pasted, we need more Chris's

Create a new Virtual Machine, choose 'Linux' as the type, 'Other Linux (64-bit)' as the version and set the memory to at least 1GB, ideally 2GB+ as ClamAV on its own needs ~1GB.

Set your new drive to at least 10GB, leave it as VDI, Dynamically Allocated

Once the machine's created, go into Settings -> System. Change the Chipset type to ICH9

Under System -> Processor, bump it up to 2 CPUs if your machine supports it

By default, under storage you'll have an IDE controller. Hit the X at the bottom to remove it

Add an AHCI controller in its place

Set the port count to 2, then hit the + disk icon on the controller

Choose the VDI created in the machine setup

Do the same with the CD icon. Choose the SME ISO if you've already added it to Virtual Media Manager. If it's not there then hit 'Add' and browse for the ISO

Disable audio. Not mandatory, but you're not going to need it

Choose a 'bridged' network adapter and make sure it's attached to your host's main network connection. This way your VM will because like a normal machine on your network and you can SSH to it

You're done - fire up the VM and the installer should start

Note - when the machine reboots you may see a 'critical error' (unless it's just my Hackintosh being weird). This is fine - just hit Ok and start it up again

Linux

Content to be done

Proxmox

Proxmox VE is a complete open-source platform for all-inclusive enterprise virtualization that tightly integrates KVM hypervisor and LXC containers, software-defined storage and networking functionality on a single platform, and easily manages high availability clusters and disaster recovery tools with the built-in web management interface.

• Hardware Requirements
• Installation

Install Proxmox #.# to suitable hardware - see proxmox wiki for details of setup

Start Proxmox, login as root, before creating a new VM there needs to be a relevant iso image available from pve storage to act as a install CD/DVD, this and other OS isos needs to be uploaded to pve local storage

Select upload button

Select a suitable iso and upload

Install/configure Koozali SME9/10 VM on proxmox VE

If not already running Start Proxmox and login as root, Select Create VM button in top right corner

Enter name details of new VM 

Select CD/DVD image file to use as install source

VM System, safe to accept defaults

Hard disk details, type/size - min of 10gb will suffice for a SME10 install

 CPU depending on hardware the more the better - 1 Socket 2 cores sufficent

Memory - minimum for sme10, 1024mb will operate sluggishly, 2048mb preferred minimum, 4096mb ideal

Network setting defaults are safe to use 

Summary of settings

Additional Hardware, Add extra hardware, change hardware settings

	Note:
	Make sure you set your default keyboard - it makes life much easier!!

We will use the vmbr0 that is set up, but we need to create a dummy one so we can put SME in server/gateway mode and use Daniels scripts:

• Create a new network interface and call it vmbr1
• Do NOT set IP address/subnet/bridge ports etc.
• Create your KVM for SME. Make sure that you give it two network adaptors - one is vmbr0 and one is vmbr1
  • vmbr0 should have the following settings :

Model: virtio

MAC: 10:10:00:00:20:20 (as per your mac that you set)

• After you have created the KVM add a second adaptor:
  • vmbr1 should have the following settings:

Model: virtio

MAC: should be the MAC of your main IP address

It doesn't matter which one is 0 or 1 as long as the settings are correct.

Select console and push start button, install will begin, interact as normal

A standalone terminal window can be seletced by selecting from top right menu - console- no vnc