Line 4: |
Line 4: |
| === Version === | | === Version === |
| {{ #smeversion: smeserver-hylafax}} | | {{ #smeversion: smeserver-hylafax}} |
− |
| |
− | {{ #smeversion: hylafax}}
| |
| | | |
| ===Maintainer=== | | ===Maintainer=== |
Line 19: |
Line 17: |
| | | |
| ===Installation=== | | ===Installation=== |
| + | ====SME8==== |
| + | |
| | | |
| yum --enablerepo=smecontribs install smeserver-hylafax | | yum --enablerepo=smecontribs install smeserver-hylafax |
| + | then issue |
| + | |
| + | signal-event post-upgrade; signal-event reboot |
| + | |
| + | ====SME9==== |
| + | you might need to install dag repo : https://wiki.contribs.org/Dag#tab=For_SME_9 |
| + | |
| + | yum --enablerepo=smecontribs,smedev,dag install smeserver-hylafax |
| + | |
| + | then you need to issue: |
| + | /sbin/e-smith/expand-template /etc/hylafax/hyla.conf |
| + | /sbin/e-smith/expand-template /etc/init/ttyS0.conf |
| + | /bin/rm -f /etc/cron.daily/hylafax |
| + | signal-event post-upgrade; signal-event reboot |
| + | |
| + | ====SME10==== |
| + | you might need to install epel repo: |
| + | |
| + | yum install smeserver-extrarepositories-epel |
| + | |
| + | then |
| + | |
| + | yum --enablerepo=smecontribs,{epel} install smeserver-hylafax |
| | | |
− | ===Enable Hylafax to start at boot=== | + | ===Enable Hylafax to start at boot (SME8 and 9 only)=== |
| | | |
| config setprop hylafax status enabled | | config setprop hylafax status enabled |
Line 37: |
Line 60: |
| | | |
| Take note of your modems port <br> | | Take note of your modems port <br> |
| + | |
| The inittab template assumes you are using ttyS0 <br> | | The inittab template assumes you are using ttyS0 <br> |
| see options below for how to change to ttyS1 <br> | | see options below for how to change to ttyS1 <br> |
| | | |
| + | For SME8 or SME9: |
| You can modify your answers later, see below <br> | | You can modify your answers later, see below <br> |
| then | | then |
Line 53: |
Line 78: |
| expand-template /etc/inittab | | expand-template /etc/inittab |
| /sbin/init q | | /sbin/init q |
| + | |
| + | for SME10: |
| + | signal-event smeserver-hylafax-update |
| + | |
| + | |
| | | |
| To Remove | | To Remove |
Line 111: |
Line 141: |
| | | |
| ports other than ttyS0, or to disable | | ports other than ttyS0, or to disable |
| + | |
| + | for SME8 and SME9: |
| | | |
| config setprop hylafax status disabled | | config setprop hylafax status disabled |
Line 116: |
Line 148: |
| /sbin/e-smith/expand-template /etc/inittab | | /sbin/e-smith/expand-template /etc/inittab |
| /sbin/init q | | /sbin/init q |
| + | |
| + | for SME10: |
| + | |
| + | config setprop hylafax port ttyS1 |
| + | signal-event smeserver-hylafax-update |
| + | |
| + | |
| | | |
| ---- | | ---- |