3,704
edits
Changes
Jump to navigation
Jump to search
mLine 7:
Line 7: − + − + − − Line 16:
Line 14: − + + + + + + + + + + − You can toggle the access property to enable public/private access.+ + + Line 43:
Line 52: − − ==Prosody version 0.9.x== − TBA − cd /root − wget http://ftpsrv01.networklab.ca/centos/6/RPMS/x86_64/prosody-0.9.4-2.el6.x86_64.rpm − wget http://ftpsrv01.networklab.ca/centos/6/RPMS/x86_64/lua-bitop-1.0.2-1.el6.x86_64.rpm − wget http://ftpsrv01.networklab.ca/centos/6/RPMS/x86_64/lua-sec-0.4.1-6.el6.x86_64.rpm − wget http://ftpsrv01.networklab.ca/centos/6/RPMS/x86_64/luajit-2.0.2-9.el6.x86_64.rpm − wget http://ftpsrv01.networklab.ca/centos/6/RPMS/x86_64/lua-zlib-0.2-1.el6.x86_64.rpm − yum localinstall *.rpm --enablerepo=epel
→Installation: update version
These instructions are for SME Server '''9.0''' 64-bit only.
These instructions are for SME Server '''9.0''' 64-bit only.
Prosody is available from the [[epel|'''epel''']] repository, so you have to enable the [[epel|'''epel''']] repository. Epel only holds the 0.8.x series of Prosody, to install or upgrade to the latest 9.x series of Prosody see below instructions.
Prosody (v0.9.12-1) is available from the [[epel|'''epel''']] repository, so you have to enable the [[epel|'''epel''']] repository. After enabling the [[epel|epel]] repository, prosody can be installed with:
After enabling the [[epel|epel]] repository, prosody can be installed with:
yum install prosody lua-ldap lua-event --enablerepo=epel
yum install prosody lua-ldap --enablerepo=epel
==Configuration==
==Configuration==
To automatically start Prosody at boot and configure the ports:
To automatically start Prosody at boot and configure the ports:
ln -s /etc/rc.d/init.d/e-smith-service /etc/rc7.d/S99prosody
ln -s /etc/rc.d/init.d/e-smith-service /etc/rc7.d/S99prosody
config set prosody service status enabled access private TCPPort 5222 UDPport 5222
config set prosody service
config setprop prosody status enabled
config setprop prosody access private
config setprop prosody TCPPort 5222
config setprop prosody UDPPort 5222
You can toggle the ''access'' property to enable public/private access.
Then to apply the new service:
signal-event remoteaccess-update
signal-event remoteaccess-update
===Configuration file===
===Configuration file===
Prosody's configuration file is located at:
Prosody's configuration file is located at:
/etc/prosody/prosody.cfg.lua
/etc/prosody/prosody.cfg.lua
{{Note box|Please note that the latest version now has split configuration files. One for server wide settings and one for each virtual host. So the below example config file should be adjusted accordingly.}}
The basic settings you have to change to run your prosody server on your domain (replace "example.com" with "yourdomain.com"):
The basic settings you have to change to run your prosody server on your domain (replace "example.com" with "yourdomain.com"):
admins = {"admin@yourdomain.com"}
admins = {"admin@yourdomain.com"}
TBA
TBA
==Documentation==
==Documentation==