3,234
edits
Changes
From SME Server
Jump to navigationJump to search→Kernel Version Issues
==Introduction==
==Introduction==
This HowTo describes how to get SME 7.x working properly on a [http://www.mini-itx.com/store/?c=34#j7f4 Jetway J7F4 Mini-ITX motherboard], or other Mini-ITX boards based on the VIA CN700 chipset. These motherboards are an extremely attractive option for builing a small, energy-efficient yet relatively fast server. The J7F4 series have two Realtek RTL8110SC Gigabit LAN adapters on board, and are powered by a VIA C7 (Ester) processor at 1.2 Ghz (with passive cooling), or at 1.5 or 2.0 Ghz with active cooling. In addition, the chipset includes hardware AES and SHA encryption/decryption, hardware MPEG2/4 decoding and a number of other potentially useful features. Unfortunately however, this hardware is not very well supported by the 2.6.9 kernel that is supplied with SME and CentOS 4. This document describes the compilation and installation of a custom kernel. It can also be used as an example of how to get SME running on or with any hardware that requires a modified or newer linux kernel.
This HOWTO describes how to get SME 7.x working properly on a [http://www.mini-itx.com/store/?c=34#j7f4 Jetway J7F4 Mini-ITX motherboard], or other Mini-ITX boards based on the [http://www.via.com.tw/en/products/chipsets/c-series/cn700/ VIA CN700] or a similar chipset. These motherboards are an extremely attractive option for building a small, energy-efficient yet relatively fast server. The J7F4 series have two Realtek RTL8110SC Gigabit LAN adapters on board, and are powered by a [http://www.via.com.tw/en/products/processors/c7/ VIA C7] (Esther) processor at 1.2 Ghz (passive cooling), or at [http://linitx.com/viewproduct.php?prodid=11337 1.5] or 2.0 Ghz with active cooling. In addition, the chipset includes hardware AES and SHA encryption/decryption, hardware MPEG2/4 decoding and a number of other potentially useful features. Unfortunately however, this hardware is not very well supported by the 2.6.9 kernel that is supplied with SME and CentOS 4. This document describes the compilation and installation of a custom kernel. It can also be used as an example of how to get SME running on or with any hardware that requires a modified or newer linux kernel.
==Procedure==
==Procedure==
===Before you start===
===Before you start===
It is always a good idea to make a backup, in case things get messed up. Furthermore, as the standard SME 7.x kernel doesn't support the RTL8110SC network controllers on board the J7F4, you might want to perform at least steps 1 through 4 on a different machine, and switch the harddisk to the Jetway machine after the new kernel is installed. If you follow the instructions below, the new kernel should run on most machines with a 686-compatible CPU (i.e. a Pentium II or higher).
It is always a good idea to make a backup, in case things get messed up. Furthermore, as the standard SME 7.x kernel doesn't support the [http://www.realtek.com.tw/products/productsView.aspx?Langid=1&PFid=4&Level=5&Conn=4&ProdID=9 RTL8110SC] network controllers on board the J7F4, you might want to perform at least steps 1 through 4 on a different machine, and switch the harddisk to the Jetway machine after the new kernel is installed. If you follow the instructions below, the new kernel should run on most machines with a 686-compatible CPU (i.e. a Pentium II or higher).
Alternatively you could install a temporary network-card in the PCI slot on the Jetway-board, or [http://forums.contribs.org/index.php?topic=35435.0 install the r1000 kernel module from Realtek]. The r1000 driver works with all RTL8169 and RTL8110 gigabit ethernet controllers. However, many people have found it to be buggy and unstable. Realtek has recently released a [ftp://209.216.61.149/cn/nic/r8169-6.001.00.tar.bz2 new version (6.001.00) of the r1000 driver], which is rumoured to fix some of the problems of earlier versions (1.05 and before). However, this version does not yet compile with newer kernel versions. You can use it with the SME/CentOS 2.6.9 kernel, but not with the new 2.6.2x kernels. As soon as you have installed the new kernel you can however switch to the r8169 kernel module. Recent versions of this driver have support for the RTL8110.
===Step 1: Installing a compiler and build tools===
===Step 1: Installing a compiler and build tools===
Processor type and features --->
Processor type and features --->
[*] Symmetric multi-processing support
Processor family (VIA C7) --->
Processor family (VIA C7) --->
(X) VIA C7
(X) VIA C7
If you have an older Mini-ITX board based on the VIA C3 processor, you should of course select the VIA C3 instead of the C7 here.
If you have an older Mini-ITX board based on a [http://www.via.com.tw/en/products/processors/c3/ VIA C3] processor, you should of course select one of the the VIA C3 options here instead of the C7. If your board has a [http://www.via.com.tw/en/products/processors/corefusion/index.jsp 'Luke' CoreFusion] or [http://www.via.com.tw/en/products/processors/eden/ Eden-N] processor (such as the VIA Epia VT or EK series Mini-ITX boards), you should probably select VIA C3-2 (Nehemiah). Symmetric multi-processing support (SMP) is only needed for dual Eden-N boards, such as the VIA Epia VT310DP.
Power management options (ACPI, APM) --->
Power management options (ACPI, APM) --->
ATA/ATAPI/MFM/RLL support --->
ATA/ATAPI/MFM/RLL support --->
<*> VIA82CXXX chipset support
<*> VIA82CXXX chipset support
Serial ATA (prod) and Parallel ATA (experimental) drivers --->
<M> ATA device support
<M> VIA SATA support
Network device support --->
Network device support --->
Ethernet (10 or 100Mbit) --->
Ethernet (10 or 100Mbit) --->
When you're done, exit and save your configuration.
When you're done, exit and save your configuration.
===Step 4: Compiling and installing the kernel===
===Step 4: Compiling and installing the kernel===
title SME Server (2.6.21-rc5-git1-custom-via)
title SME Server (2.6.21-rc5-git1-custom-via)
root (hd0,0)
root (hd0,0)
kernel /vmlinuz-2.6.21-rc5-git1-custom-via ro root=/dev/hda6
kernel /vmlinuz-2.6.21-rc5-git1-custom-via ro root=/dev/main/root
initrd /initrd-2.6.21-rc5-git1-custom-via.img
initrd /initrd-2.6.21-rc5-git1-custom-via.img
Before rebooting, you should tell SME what driver you want to use for the on-board ethernet controllers.
Before rebooting, you should tell SME what driver you want to use for the on-board ethernet controllers.
If your board has RealTek RTL8169 or RTL8110 gigabit ethernet controllers (e.g. the Jetway J7F4 or the [http://www.mini-itx.com/store/?c=34#modules 3x Gigabit LAN extension module] for the [http://www.mini-itx.com/store/?c=34#j7f2 Jetway J7F2]), you'll want to use the r8169 driver:
If your board has RealTek RTL8169 or RTL8110 gigabit ethernet controllers (e.g. the Jetway J7F4 or the [http://linitx.com/viewcategory.php?catid=140 3x Gigabit LAN extension module] for the [http://linitx.com/viewcategory.php?catid=141 Jetway J7F2]), you'll want to use the r8169 driver:
/sbin/e-smith/config set EthernetDriver1 r8169
/sbin/e-smith/config set EthernetDriver1 r8169
/sbin/e-smith/config set EthernetDriver2 r8169
/sbin/e-smith/config set EthernetDriver2 r8169
If your board has dual VIA 10/100 Mbit ethernet controllers (e.g. the [http://www.mini-itx.com/store/?c=2#epiavt VIA Epia VT series]), you'll want to use the via-rhine driver:
If your board has dual VIA 10/100 Mbit ethernet controllers (e.g. the [http://www.mini-itx.com/store/?c=2#epiavt VIA Epia VT] or [http://linitx.com/viewproduct.php?prodid=11134 Epia EK] series), you'll want to use the via-rhine driver:
/sbin/e-smith/config set EthernetDriver1 via-rhine
/sbin/e-smith/config set EthernetDriver1 via-rhine
===Step 6: Final configuration===
===Step 6: Final configuration===
If all has gone well, you should now be up and running on your brand new kernel. All that remains is to make sure that any remaining 'extra features' are loaded into the kernel. If you are running on a VIA CN700 based board such as the Jetway J7F4 / J7F2 or the VIA Epia VT / EK series, try the following to enable hardware crypting support:
If all has gone well, you should now be up and running on your brand new kernel. All that remains is to make sure that any remaining 'extra features' are loaded into the kernel. If you are running on a VIA Eden, Eden-N or 'Luke' CoreFusion board such as the Jetway J7F4 / J7F2 or the VIA Epia VT / EK series, try the following to enable hardware crypting support:
/sbin/modprobe via-rng
/sbin/modprobe via-rng
/sbin/modprobe padlock
/sbin/modprobe padlock
And in the unlikely event that you want to run an Xserver with hardware accellerated 2D graphics and MPEG-decoding:
And in the unlikely event that you want to run an Xserver with hardware accelerated 2D graphics and MPEG-decoding:
/sbin/modprobe via
/sbin/modprobe via
echo ondemand >/sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
echo ondemand >/sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
If you have a dual core or dual processor board, you should do this for the second processor as well:
echo ondemand >/sys/devices/system/cpu/cpu1/cpufreq/scaling_governor
Of course, you don't want to type all of this every time you reboot the server. So you can create a script in /etc/e-smith/events/local that will configure things for you at boot-time:
Of course, you don't want to type all of this every time you reboot the server. So you can create a script in /etc/e-smith/events/local that will configure things for you at boot-time:
#!/bin/sh
#!/bin/sh
# Custom initialisation stuff for the VIA C7
# Custom initialisation stuff for the VIA C7
/sbin/modprobe via_rng
/sbin/modprobe via_rng
/sbin/modprobe padlock
/sbin/modprobe padlock
echo ondemand >/sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
echo ondemand >/sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
# Uncomment the following for dual-processor boards:
# echo ondemand >/sys/devices/system/cpu/cpu1/cpufreq/scaling_governor
Save the script (F2 or F10 in mcedit) and set the right permissions:
Save the script (F2 or F10 in mcedit) and set the right permissions:
You can also delete the remaining packages and sources in /usr/src, if you wish.
You can also delete the remaining packages and sources in /usr/src, if you wish.
==Other Tips & Tricks==
According to [http://www.tkarena.com/forums/linux-arena/32095-j7f4k-hard-lockups-14.html#post228588 this thread], the chipset used on many VIA C7-based boards is quite sensitive to overheating. This may cause lockups during high disk activity, especially if your board is passively cooled and in a small case.
Jetway has released a [http://download.jetway.com.tw/download.asp?sorder=Name&sword=J7F4K1G5D new BIOS version (A07) for J7F4 boards] that seems to more or less fix this problem. To flash it, you'll need to [http://www.nenie.org/misc/flashbootcd.html boot the board in DOS] and use the [http://download.jetway.com.tw/download/utilities/awdflash.zip Award flash utility]. If you keep experiencing mysterious lockups after the BIOS-update, it is advisable to add a CPU- or case-fan or to fit the board into a bigger case.
Jetway have released a new revision of the J7F4 mainboard, which incorporates a bigger heatsink in conjunction with the new BIOS to solve the overheating problems. Thanks to Ryan Salsbury for pointing this out. Ryan has also kindly provided pictures of the old and new board revisions:
* [http://www2.multithread.co.uk/mtcshop/images/linitx.com/products/Jetway_J7F4K_1.2GHz_EDEN_Mainboard_-_Dual_GigaLAN_main.jpg The board with the old, small heatsink]
* [http://www2.multithread.co.uk/mtcshop/images/linitx.com/products/Jetway_J7F4K_1.2GHz_EDEN_Mainboard_-_Dual_GigaLAN_rear.jpg Rear view of the old board]
* [http://www2.multithread.co.uk/mtcshop/images/linitx.com/products/Jetway_J7F4K_1.2GHz_Eden_CN700_Mainboard_-_Dual_GigaLAN_-__NEW_REVISION_main.jpg New board, with larger heatsink]
* [http://www2.multithread.co.uk/mtcshop/images/linitx.com/products/Jetway_J7F4K_1.2GHz_Eden_CN700_Mainboard_-_Dual_GigaLAN_-__NEW_REVISION_front.jpg Front view of the new board]
* [http://www2.multithread.co.uk/mtcshop/images/linitx.com/products/Jetway_J7F4K_1.2GHz_Eden_CN700_Mainboard_-_Dual_GigaLAN_-__NEW_REVISION_rear.jpg Rear view of the new board]
* [http://www2.multithread.co.uk/mtcshop/images/linitx.com/products/Jetway_J7F4K_1.2GHz_Eden_CN700_Mainboard_-_Dual_GigaLAN_-__NEW_REVISION_side.jpg Side view of the new board]
* [http://www2.multithread.co.uk/mtcshop/images/linitx.com/products/Jetway_J7F4K_1.2GHz_Eden_CN700_Mainboard_-_Dual_GigaLAN_-__NEW_REVISION_Overview.jpg Overview of the new board]
==Kernel Version Issues==
People have reported that USB drive recognition will no longer work after updating the kernel. This is due to the fact that the udev version used in CentOS 4 will not work with kernel versions above 2.6.12. You will need to update the udev package. I will update this Howto as soon as I have tried this myself. In the mean time, you may find newer udev versions here: ftp://ftp.kernel.org/pub/linux/utils/kernel/hotplug/
Another problem is that the custom kernel may cause problems when trying to upgrade SME. On any update that includes a newer kernel, yum will complain about dependency problems because the custom kernel has a higher version-number than the kernel that is to be updated. The only way around this seems to be to uninstall the custom kernel (using yum remove ...), do the upgrade, and then re-install the custom kernel before rebooting.
You can also use the exclude package option to avoid kernel and kmod updates, and everything will just work fine !
==Author and Acknowledgements==
==Author and Acknowledgements==
This HowTo is written by Levien van Zon (levien at scum.org). It is based to a large extent on forum postings and documents by Harro, Charlie Brady, Falko Timme, Simon Arlott and many others. See the references below for more information. This document may still contain mistakes and typos, so please feel free to add or correct things if you have wiki-access. You can also send corrections and suggestions to the author by e-mail.
This Howto is written by Levien van Zon (levien at scum.org). It is based to a large extent on forum postings and documents by Harro, Charlie Brady, Falko Timme, Simon Arlott, Neil, Ryan Salsbury and many others. See the references below for more information. This document may still contain mistakes and typos, so please feel free to add or correct things if you have wiki-access. You can also send corrections and suggestions to the author by e-mail.
==References==
==References==
* http://lkml.org/lkml/2007/2/12/428
* http://lkml.org/lkml/2007/2/12/428
* http://acpi.sourceforge.net/documentation/processor.html
* http://acpi.sourceforge.net/documentation/processor.html
* http://forums.viaarena.com/messageview.aspx?catid=28&threadid=77032
[[Category:Howto]]
[[Category:Howto]]
