681
edits
Changes
Jump to navigation
Jump to search
Line 2:
Line 2: + + − + Line 15:
Line 17: + + + + + + + + + + + + + + + + + + + + + + + − + + + Line 33:
Line 60: + + Line 49:
Line 78: + + + + + Line 107:
Line 141: + + Line 112:
Line 148: + + + + + + + Line 143:
Line 186: + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + Line 151:
Line 228: + + + + + + + +
no edit summary
==HylaFAX for SME Server==
==HylaFAX for SME Server==
{{Level|Advanced}}
{{Level|Advanced}}
=== Version ===
{{ #smeversion: smeserver-hylafax}}
===Maintainer===
===Maintainer===
http://www.dungog.net
http://www.dungog.net<br />
===Description===
===Description===
===Installation===
===Installation===
====SME8====
yum --enablerepo=smecontribs install smeserver-hylafax
yum --enablerepo=smecontribs install smeserver-hylafax
then issue
signal-event post-upgrade; signal-event reboot
====SME9====
you might need to install dag repo : https://wiki.contribs.org/Dag#tab=For_SME_9
yum --enablerepo=smecontribs,smedev,dag install smeserver-hylafax
then you need to issue:
/sbin/e-smith/expand-template /etc/hylafax/hyla.conf
/sbin/e-smith/expand-template /etc/init/ttyS0.conf
/bin/rm -f /etc/cron.daily/hylafax
signal-event post-upgrade; signal-event reboot
====SME10====
you might need to install epel repo:
yum install smeserver-extrarepositories-epel
then
===Enable Hylafax to start at boot===
yum --enablerepo=smecontribs,{epel} install smeserver-hylafax
===Enable Hylafax to start at boot (SME8 and 9 only)===
config setprop hylafax status enabled
config setprop hylafax status enabled
Take note of your modems port <br>
Take note of your modems port <br>
The inittab template assumes you are using ttyS0 <br>
The inittab template assumes you are using ttyS0 <br>
see options below for how to change to ttyS1 <br>
see options below for how to change to ttyS1 <br>
For SME8 or SME9:
You can modify your answers later, see below <br>
You can modify your answers later, see below <br>
then
then
expand-template /etc/inittab
expand-template /etc/inittab
/sbin/init q
/sbin/init q
for SME10:
signal-event smeserver-hylafax-update
To Remove
To Remove
ports other than ttyS0, or to disable
ports other than ttyS0, or to disable
for SME8 and SME9:
config setprop hylafax status disabled
config setprop hylafax status disabled
/sbin/e-smith/expand-template /etc/inittab
/sbin/e-smith/expand-template /etc/inittab
/sbin/init q
/sbin/init q
for SME10:
config setprop hylafax port ttyS1
signal-event smeserver-hylafax-update
----
----
-n -u uucp "$EXT2@`/usr/bin/expr \"$HOST\" : '\(.*\)\.fax$'`" \
-n -u uucp "$EXT2@`/usr/bin/expr \"$HOST\" : '\(.*\)\.fax$'`" \
"$SENDER"
"$SENDER"
Further customizations are possible:
/usr/bin/faxmail -s a4 \
-n -N -T -u uucp -t done "$EXT2@`/usr/bin/expr \"$HOST\" : '\(.*\)\.fax$'`" \
"$SENDER"
-N -> this switch disable the faxmail Cover Page, otherwise autogenerated translating the mail header: this may be an "unuseful" cover with a mostly blank page;
-T -> this switch can disable empty blank pages at the end of your fax;
-t done -> in this way you can get your notification (receipt) concerning your fax transaction for both succesfull or failed faxes; this is a sample of the success message you'll receive in your mailbox:
Your job to 011654321 was completed successfully.
Pages: 1
Receiver: 011 99988812
Quality: 196
Page Width: 209 (mm)
Page Length: 296
Signal Rate: 9600 bit/s
Data Format: 2-D MMR
Remote Equipment: unknown
Remote Station:
Dialogs: 1 (exchanges with remote device)
Calls: 1 (total phone calls placed)
Modem: any
Submitted From: localhost
JobID: 28
GroupID: 28
CommID: c000000077
Processing time was 1:07.
The fax is attached as a pdf file if not selected otherwise another file format.
{{Note box|In the previous commands the paper size is set to A4 with the '<tt>-s</tt>' option. Paper sizes that can be with this option are:
{{Note box|In the previous commands the paper size is set to A4 with the '<tt>-s</tt>' option. Paper sizes that can be with this option are:
* <tt>NA-LET</tt> ''(US Letter)''
* <tt>NA-LET</tt> ''(US Letter)''
=== Bugs ===
=== Bugs ===
Please raise bugs under the SME-Contribs section in {{BugzillaFileBug|product=|component=|title=bugzilla}}and select the smeserver-hylafax component or use {{BugzillaFileBug|product=SME%20Contribs|component=smeserver-hylafax|title=this link}}.
Please raise bugs under the SME-Contribs section in {{BugzillaFileBug|product=|component=|title=bugzilla}}and select the smeserver-hylafax component or use {{BugzillaFileBug|product=SME%20Contribs|component=smeserver-hylafax|title=this link}}.
{{#bugzilla:columns=id,product,version,status,summary |sort=id |order=desc |component=smeserver-hylafax|noresultsmessage="No open bugs found."}}
===Changelog===
Only released version in smecontrib are listed here.
{{ #smechangelog: smeserver-hylafax}}
----
----