NFS

How To use SME as an NFS server

This came from a dtech post about to use SME as a NFS server

	Note:
	you have some documentation available for CENTOS6 and CENTOS5

Installation

for sme8

1. Install the smeserver-nfs contrib like this:

yum install smeserver-nfs --enablerepo=smecontribs

2. Then execute the following:

• sme8

config setprop nfs status enabled
config setprop portmap status enabled
config setprop nfslock status enabled

3. Edit /etc/exports to add the directories to be shared (this line exports user home directories and ibays):

/home/e-smith/files    *.mydomain(rw,sync,no_wdelay,nohide,no_root_squash)

/home/e-smith/files  – shared directory

192.168.1.0/24           – IP address range of clients
or
*.mydomain               – Domain's client allowed

rw                       – Writable permission to shared folder
sync                     – Synchronize shared directory
no_root_squash           – Enable root privilege
no_all_squash            – Enable user’s authority

if you want to see all your exports

showmount -e

	Warning:
	Make sure to leave a blank line at the end of the file.

securing NFS Securing2

4. Then, the following, which will reboot the server:

signal-event post-upgrade; signal-event reboot

Couple of notes whilst installing on SME8.....

DB options as follows - status disabled by default :

nfs=service
   TCPPorts=2049,4002,4003
   UDPPorts=2049,4002,4003
   access=private
   mountdPort=4002
   rquotadPort=4003
   status=disabled

nfslock=service
   TCPPorts=4000,4001,4004
   UDPPorts=4000,4001,4004
   access=private
   lockdPort=4001
   statdOutgoingPort=4004
   statdPort=4000
   status=disabled

portmap=service
   TCPPort=111
   UDPPort=111
   access=private
   status=disabled

After installation & reboot you should be able to update with

signal-event remoteaccess-update

However, I don't think this starts/restarts portmap, hence the reboot on install which should not really be necessary.

for sme9

It is for really soon --Stephdl (talk) 00:18, 7 December 2014 (CET) Remember to first configure the required stephdl repository, then issue the following command on the SME Server shell:

yum install --enablerepo=stephdl smeserver-nfs

You need to activate the service

chkconfig nfs on
signal-event nfs-update
config set UnsavedChanges no

or if you prefer to restart your server

signal-event post-upgrade; signal-event reboot

	Note:
	For security Reasons you can not enable Your NFS Share in 'Read and Write, No Root Squash and Insecure' options for the whole local network, you have to specify each IP allowed for these insecure settings.

If you want modify the Group Ownership or user access permissions, these changes has to be done in the Ibay Panel.

Usage

• Each IP needs to be allowed if you want write permission. For read only permissions, you can open the share to all defined local network in the server-manager
• The NFS share works with Ibays whose the system of permissions are Group based and inherited from the ibay panel. Therefore for changing write/read and group permissions you need to do it in the Ibay panel. You have at the top of the NFS panel a description on the state of permissions and the group ownership.
• NFS works with UID and GID, the user id and group id of the client system are sent in each RPC call, and the permissions these IDs have on the file being accessed are checked on the server. For this to work, the UID and GIDs must be the same on the server and the clients.
• read permissions :

- you can easily allow the share in read permission for the local network and for all defined IP (go to the ibay panel and set the User access to write=group, read=everyone, enabled the share, and allow ip or the local network.)

• Write and read permission for group:

- you have to set a group who own the ibay (in the ibay panel) and change the permissions to Write=group, Read=Group

- All users both in the server and in the clients need to be members of that group with the same GID.

- you have to share the same UID for users between the server and the client

for example the user Helene must share the same UID and GID between the SME Server and the remote client

on remote client
# id helene
uid=5006(helene) gid=5006(helene) groupes=5006(helene),5002(famille)
on SME Server
# id helene
uid=5006(helene) gid=5006(helene) groupes=5006(helene),500(shared),5002(famille)

-IF the option no_root_squash is set, the root can still write in the ibay, but the issue, is that all root or sudo users of all server allowed to the nfs share can write without controls in the ibay.

UID/GID

• create a group

groupadd -g GID -o GROUPE_NAME

• modify the GID of a group

groupmod -o -g GID GROUPE_NAME

• add a principal group to a user

usermod -g GROUP_NAME_OR_GID USER_NAME

• add a secondary group to a user

usermod -a -G GROUP_NAME_OR_GID USER_NAME

• change the uid of a user

usermod -u UID USER_NAME

• see informations of a user

id USER

Couple of notes whilst installing on SME9.....

DB options as follows - status enabled by default :

nfs=service
   TCPPorts=2049,4002,4003
   UDPPorts=2049,4002,4003
   access=private
   mountdPort=4002
   rquotadPort=4003
   status=enabled

nfslock=service
   TCPPorts=4000,4001,4004
   UDPPorts=4000,4001,4004
   access=private
   lockdPort=4001
   statdOutgoingPort=4004
   statdPort=4000
   status=enabled

rpcbind=service
   TCPPort=111
   UDPPort=111
   access=private
   status=enabled

you should be able to update with

signal-event nfs-update

see exported folders

You can have a look on all exported folders and see for which ip/network they are allowed.

# showmount -e
Export list for hpcompact:
/home/e-smith/files/ibays/toto/files        192.168.15.0/24,192.168.12.0/24
/home/e-smith/files/ibays/laurence/files    192.168.12.100,192.168.12.125
/home/e-smith/files/ibays/dolibarr/files    192.168.15.0/24,192.168.12.0/24
/home/e-smith/files/ibays/admin_25465/files 192.168.15.0/24,192.168.12.0/24

find connected clients

netstat -an | grep nfs.server.ip:port

• for example

# netstat -an | grep 192.168.12.125:2049
tcp        0      0 192.168.12.125:2049         192.168.12.25:850           ESTABLISHED 

client side

• nfs-comon

install nfs-common (it depends of your distribution)

• mount the network share

mkdir /mnt/partage
mount -t nfs 192.168.xx.xxx:/home/e-smith/files /mnt/partage
ll /mnt/partage

ToDos

Probably better to make a custom template for /etc/exports

Would be better if there was a web panel to enable/disable nfs per ibay