Vmware

Languages:

English  • Deutsch

Maintainer

Sme Developers

Description

VMware Server installs on any existing server hardware and partitions a physical server into multiple virtual machines by abstracting processor, memory, storage and networking resources, giving you greater hardware utilization and flexibility. Streamline software development and testing and simplify server provisioning as you utilize the ability to "build once, deploy many times."

Installation

http://forums.contribs.org/index.php?topic=37605.0

http://forums.contribs.org/index.php?topic=30838.msg162804#msg162804

VMware Server 1.x and 2.x

Installation

Get shell access (with Putty, Gnome-terminal or similar ssh-client) and log in as root.

Download the VMWare-server 1.x RPM from the VMWare website to your machine (VMWare Server 1 Website)
VMware Server 2.x can't be downloaded directly from VMware servers, so get it to your server in some other way. (VMWare Server 2 Website)

wget http://download3.vmware.com/software/vmserver/VMware-server-1.0.7-108231.i386.rpm

Issue the following command to install VMware together with the contrib:

yum install /path/to/VMware-server.rpm smeserver-vmware-server --enablerepo=smecontribs

The above should also install xinetd for dependency.

Updating

Updating is similar to installation. You will need to download the latest rpm for example:

wget http://download3.vmware.com/software/vmserver/VMware-server-1.0.7-108231.i386.rpm

Issue the following command:

yum localupdate path/to/VMWare-server.rpm

You will also likely have to rerun the Configuration steps (below)

Configuration

Go to VMware web site and get a free serial number for VMware Server, linux version here.

	Note:
	The requirement for GCC is currently optional. Depending on your kernel at the time you may find the the included modules load and run perfectly (it will give you a message to this effect). Enabling repos help resolve dependencies. yum install gcc

To finish the installation run the following command:

vmware-config.pl

	Warning:
	Leaving gcc on a production server is considered a security risk, if you do not really need it you should not install it, if you need it you should seriously consider uninstalling gcc when you no longer need it. Removing gcc can be done using the following command: yum remove gcc

Clean up after the installation:

signal-event post-upgrade; signal-event reboot

Management UI for VMWare Server 1.x

Installation

VMware Server Web-based management interface. It's optional, you can also use VMware Console from a client computer.

wget http://download3.vmware.com/software/vmserver/VMware-mui-1.0.6-91891.tar.gz
tar -xzvf VMware-mui-1.0.6-91891.tar.gz

cd vmware-mui-distrib/

Configuration

Configuration of the management user interface is done with a script that can be run like this:

./vmware-install.pl

Remote access

The VMware Server will only be accessible from the local network. If you want to be able to access the VMware Server from internet, run these commands:

Console

To allow console access from your local network:

config set vmware service access private status enabled TCPPort 902

	Warning:
	The command below will open the ports of the Management Console to the internet, this means a serious security implication

To allow console access from all over the internet:

config set vmware service access public status enabled TCPPort 902

Update the remote access settings and reload changes:

signal-event remoteaccess-update

Substitute "disabled" instead of "enabled" in the above commands to disable access.

Management UI

To allow Management UI access from your local network:

config set httpd.vmware service TCPPorts 8222,8333 access private status enabled

	Warning:
	The command below will open the ports of the Management UI to the internet, this means a serious security implication

To allow Management UI access from all over the internet:

config set httpd.vmware service TCPPorts 8222,8333 access public status enabled

After defining the service we need to make the service start at boot time

ln -s /etc/rc.d/init.d/e-smith-service /etc/rc7.d/S91httpd.vmware

Now we can manually start the service

/etc/rc7.d/S91httpd.vmware restart
signal-event remoteaccess-update

Substitute "disabled" instead of "enabled" in the above commands to disable access.

Usage

Management Console for VMware Server 1.x

Download and install the VMware console from the VMware web site, or the MUI webpage, on a client machine or use the existing console if you already have VMware (Server) installed.

Run Console on your client and connect to your_server and start to play...

Management UI for 1.x

Open a web browser and go to https://your_server:8333/vmware/en/

Log in as root and you will find VMware Management interface.

Management UI for 2.x

Open a web browser and go to https://ip.of.your.server:8333/ui/#

Log in as the user you specified during configuration, and you will find VMware Management interface.

Uninstallation

vmware-uninstall-mui.pl
yum remove VMware-server gcc smeserver-vmware-server

Check installed versions

yum info installed smeserver-vmware-server VMware-server

Additional information

More information about vmware can be found on the vmware website http://www.vmware.com/products/server/

If some setting went wrong during installation, just rerun

vmware-config.pl 

NB. VMware-server benefits from a lot of ram.

Bugs

Please raise bugs under the SME-Contribs section in bugzilla and select the smeserver-vmware-server component or use this link .

Known problems

Be aware that a yum update that includes a new kernel may cause a failure of VMware-server. In this case, you will have to re-run vmware-config.pl and rebuild the modules.

Virtual machines created in a Windows host probably need further customization to work fully under SMEserver (Linux) host.

Installing VMware Server 2 without the contrib smeserver-vmware-server will likely result in failure to start VMware after a reboot.
If that is your case you probably have to reinstall the whole server before attempting to install VMware again.

---