IAXModem with Sail and HylaFax
Introduction
This Howto is aimed at the installation of IAXModem in conjunction with SAIL/asterisk and Hylafax in order to provide a fax over VOIP solution. It is based on information from various forum posts including:
http://forums.contribs.org/index.php/topic,39258.msg179460.html
http://forums.contribs.org/index.php/topic,41256.msg219493.html
Sail and Asterisk Setup
Global Settings
In Global Settings
- Make sure that 'Late Termination' is set to No.
- Make sure that the 'Autosense FAX Extension' is set to a number you want to use for the Fax. You will need this number later.
- The 'Fax Delay' setting defaults to 2 seconds. You may need to adjust this later to make sure faxes get detected before asterisk attempts to terminate somewhere other than the FAX.
Trunklines
For each of the Trunks under Trunklines that you want to be able to detect incoming Faxes on
- Make sure that the 'Fax' detection tick box is ticked
- Include a 'Transformation String' of
99:
Fax Route
Create a new Route for faxes with dialplan(s) starting with 99.
example: 99X.
and with Paths pointing to the Trunks you wish to receive faxes with 'Fax' detection ticked as above
Fax Extension
Create a new Extension with the same number as set in the 'Autosense FAX Extension' as above - or vice versa. The 'Device' should be IAXModem.
Once created check the stanza generally conforms to the following and change as necessary:
[2000] type=friend username=FaxModem secret=asterisk host=dynamic qualify=3000 context=internal callerid="Faxmodem" <2000> disallow=all allow=slin
IAXModem
Installation
Download the iaxmodem rpm from Aelintra and install
wget http://sarkpbx.com/sail/iaxmodem/iaxmodem-1.0.0-1.noarch.rpm yum localinstall iaxmodem-1.0.0-1.noarch.rpm
Configuration
Check and edit /etc/iaxmodem/ttyIAX0 as necessary:
device /dev/ttyIAX owner uucp:uucp mode 660 port 4570 refresh 60 server 127.0.0.1 peername 2000 secret asterisk cidname YourCompany cidnumber 0123456789 codec slinear
Check and Run
Check the modem registers with Sail and Asterisk
/usr/local/sbin/iaxmodem ttyIAX
should give an output similar to
Modem started Setting device = '/dev/ttyIAX' Setting owner = 'uucp:uucp' Setting mode = '660' Setting port = 4570 Setting refresh = 60 Setting server = '127.0.0.1' Setting peername = '2000' Setting secret = 'asterisk' Setting cidname = 'YourCompany' Setting cidnumber = '0123456789' Setting codec = slinear Opened pty, slave device: /dev/pts/0 Created /dev/ttyIAX symbolic link Registration completed successfully.
and in an asterisk CLI
--Registered IAX2 '2000' (AUTHENTICATED) at 127.0.0.1:4570
Now
db configuration set iaxmodem service status enabled /etc/rc.d/rc7.d/S93iaxmodem start
HylaFax
Install the smeserver-hylafax contrib. When you run faxsetup, at the end it will ask to continue and run faxaddmodem to setup a modem. Choose ttyIAX as the modem port and continue and set other values as required. Do not reboot or start HylaFax yet. Edit /etc/hylafax/etc/config.ttyIAX and add
ModemDialCmd: ATDT99%s
This will prefix all numbers dialled by HylaFax with 99 so they can be identified and routed by SAIL Also check
# make attachments readable RecvFileMode: 0666 LogFileMode: 0666 DeviceMode: 0666 # for shared lines set to 10 RingsBeforeAnswer: 1 # change to suit SpeakerVolume: quiet LocalIdentifier: "YourCompany"
Now if you want you can configure who receives faxes by editing
/etc/hylafax/etc/FaxDispatch
Finally set the modem port in the database
db configuration setprop hylafax port=ttyIAX /sbin/e-smith/expand-template /etc/inittab
Now continue with the contrib setup for Hylafax
iaxmodem Startup Script
The following is the code for the /etc/rc.d/init.d/iaxmodem script from the current iaxmodem-1.2.0.tar.gz source.
#!/bin/sh
# Startup script for iaxmodem
#
# chkconfig: 2345 95 05
# description: IAXModem for asterisk <-> Hylafax gateway
# Source function library.
. /etc/rc.d/init.d/functions
[ -f /usr/local/sbin/iaxmodem ] || exit 0
prog="IAXmodem"
start() {
echo -n $"Starting $prog: "
daemon /usr/local/sbin/iaxmodem
RETVAL=$?
echo
return $RETVAL
}
stop() {
if test "x`pidof iaxmodem`" != x; then
echo -n $"Stopping $prog: "
killproc iaxmodem
echo
fi
RETVAL=$?
return $RETVAL
}
reload() {
if test "x`pidof iaxmodem`" != x; then
echo $"Reloading $prog"
kill -HUP `head -1 /var/run/iaxmodem.pid`
fi
}
case "$1" in
start)
start
;;
stop)
stop
;;
status)
status iaxmodem
;;
reload)
reload
;;
restart)
stop
start
;;
condrestart)
if test "x`pidof iaxmodem`" != x; then
stop
start
fi
;;
*)
echo $"Usage: $0 {start|stop|reload|restart|condrestart|status}"
exit 1
esac
exit $RETVAL
