Difference between revisions of "Uninterruptable Power Supply"
Unnilennium (talk | contribs) |
|||
| Line 346: | Line 346: | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | =Scheduling Events= | + | ===Scheduling Events=== |
====Shutdown Time Delay Example==== | ====Shutdown Time Delay Example==== | ||
Revision as of 09:31, 17 January 2024
Is this article helpful to you?
Please consider donating or volunteering
Thank you!
Uninterruptable Power Supply
Introduction
The primary goal of the Network UPS Tools (NUT) project is to provide reliable monitoring of UPS hardware and ensure safe shutdowns of the systems which are connected.
The default configuration of NUT, will keep your connected systems operational until a critical battery state is reached (ie battery is nearing exhaustion) and then power down your server/equipment in a controlled fashion. See http://www.networkupstools.org/
If you have an APC UPS, see also Uninterruptable_Power_Supply:APC for an alternative to the standard SME Nut implementation
If you have Dell UPS, this might Help Uninterruptable_Power_Supply:LatestGeekery
Default Configuration (USB)
The default configuration in SME Server for 'NUT' is set by the configuration database properties
Model = usbhid-ups status = disabled type = service
Most USB connected UPS's will work with these default settings. If using a USB connection just enable NUT as follows:
For SME 10, systemd is now in use. We have created a generic service for your convenience:
config setprop nut status enabled signal-event e-smith-nutUPS-update systemctl restart nut-server.service systemctl restart nut-monitor.service systemctl restart nut.service
config setprop nut status enabled signal-event post-upgrade signal-event reboot
If your USB UPS does not work properly OR you have a serial device then follow the Configuration Options below as required.
Configuration Options
Not all UPS's are supported by USB or the usbhid-ups driver. However NUT supports many UPS's and can be configured under SME Server easily.
Serial Connection
- Find the configuration details for your model of UPS. Refer to: http://www.networkupstools.org/stable-hcl.html and make note of the driver name and upstype number (if any) in the third column.
- From the console issue the following commands:
config setprop nut Model <model>
config setprop nut Device <device>
config setprop nut Type <type>
config setprop nut status enabled
Where:
<model> and <type> are the driver name and type number found above.
<device> is the serial port that the UPS is connected to eg. /dev/ttyS0. It also possible to use a more readable symlink. See HowTo on udev - symlinks for details. Note: The case of Model, Device and Type. - Check: config show nut
- Apply changes and restart server: signal-event post-upgrade signal-event reboot Alternatively, without NUT running or requiring a server reboot: signal-event console-save service nut start
- Confirm server is communicating with UPS: upsc UPS@localhost Whenever a UPS event occurs Emails are sent to the admin account.
Configuring as a master
edit the file /etc/ups/nut.conf, and modify the line
MODE=netserver
Set configuration values:
config setprop nut access private TCPPort 3493 expand-template /etc/ups/upsd.conf expand-template /etc/rc.d/init.d/masq systemctl restart masq systemctl restart nut-server
Configuring as a slave
Set configuration values:
config setprop nut SlaveUPS UPS@192.168.33.11 config setprop nut Master no
Where 192.168.33.11 is your UPS master, that is the computer that is in direct communication with the UPS. The hostname of that computer may also work.
Apply changes and restart server:
signal-event post-upgrade signal-event reboot
or (for SME10):
signal-event e-smith-nutUPS-update
Confirm server is communicating with master:
upsc UPS@192.168.33.11
Connecting multiple UPS's
To be added http://bugs.contribs.org/show_bug.cgi?id=629
rpm -qa e-smith-nutUPS
If you get NUT running with administrative privileges modification from sme8 instruction, you need to remove the custom template created for this. These variables are taken in charge by the new package.
First you need to delete the custom template file.( This command delete the directory, be sure you don't have personal file present. If the case, delete manualy the file created for administrative privileges )
rm -rf /etc/e-smith/templates-custom/etc/ups/upsd.users
Now, to get upsd to recognise the modification of user, we need to expand the template and reload the upsd configuration
/sbin/e-smith/expand-template /etc/ups/upsd.users /usr/sbin/upsd -c reload
UPS Variables and Commands
In some cases you may wish to modify variables on the actual UPS such as the Low Charge/LOWBATTERY setting. This requires the use of the upsrw command and UPS administrative privileges.
You may also want to control the UPS directly from the command line by issuing UPS commands. This requires use of the upscmd command and UPS administrative privileges.
UPS Administrative Privileges
You should check your new password ( AdminPass ) to run upserw & upscmd. Of course, you could change your password for a easier one to use.
config show nut
To set new admin password in database. The new password would be admin ( change it to suit your need )
config setprop nut AdminPass admin
To enabled administrative privileges and run command to ups.
config setprop nut AdminUser enabled
Now, to get upsd to recognise admin modification for administrative privileges we expand the template and reload the upsd configuration
/sbin/e-smith/expand-template /etc/ups/upsd.users /usr/sbin/upsd -c reload
UPS access
The access of the ups is controled by database properties. The default propertie is set to localhost and give permission to run upsrw & upscmd from localhost only if administrative privileges is set to enabled as above. No slave ups could be connected in this mode. Three choices is available to set access.
- localhost: the ups access is only from the local machine ( UPS master ).
- private: the ups access is from your local machine and local network as per define in server-manager panel.
- public: the ups access is similar to localhost.
To set access properties in the database ( example: localhost )
config setprop nut access localhost /sbin/e-smith/expand-template /etc/ups/upsd.conf /usr/sbin/upsd -c reload
In localhost or public mode ( no remote access ), access to your ups is ( UPS name is UPS )
UPS@localhost
In private mode, access to your ups is ( UPS name is UPS )
UPS@localhost or UPS@192.168.1.1 ( ups master IP ) slave ups get access with UPS@192.168.1.1 ( ups master IP )
Setting UPS Variables
In order to set UPS variables it is necessary to have enabled the administrative privileges as above first and you get the possibility to run command from slave ups if access is set to private as above.
In the examples below, it is assumed your UPS name is UPS, that it is local, that the administrative user is admin and password admin. You can verify your UPS name via:
upsc -l
To view a complete list of the UPS variables, both informational and modifiable
upsc UPS
To determine the modifiable variables for your UPS, their current settings and their available setting values execute the command:
upsrw UPS
You can now modify the variables you wish using a command similar to the following (Note the order of the arguments is important, and you may need quotes around the value being set, "20"):
upsrw -s battery.charge.low=20 -u admin -p admin UPS
For remote host (slave UPS ), we need to add the IP from master UPS to run command.
upsrw -s battery.charge.low=20 -u admin -p admin UPS@192.168.2.1
Where the value after -s should be one of the parameters identified by the upsrw ups command. You can of course verify your changes using
upsrw UPS
or
upsc UPS
After you are done, clean up by disabling the upsc administrative privileges:
More information on upsrw can be found at:
- Manual page: man upsrw
Issuing UPS Commands
In order to issue UPS commands it is necessary to have enabled the administrative privileges as above first and you get the possibility to run command from slave ups if access is set to private as above.
In the examples below, it is assumed your UPS name is UPS, that it is local, that the administrative user is admin and password admin. You can verify your UPS name via:
upsc -l
To view a complete list of available commands for your UPS:
upscmd -l UPS
You can now issue a command to the localhost UPS with similar to the following:
upscmd -u admin -p admin UPS test.battery.start
For remote host (slave UPS ), we need to add the IP from master UPS to run command.
upscmd -u admin -p admin UPS@192.168.2.1 test.battery.start
Where the command test.battery.start is a valid command for your UPS as previously determined by upscmd -l UPS. Depending upon the command issued you may get broadcast messages and emails relating to and confirming what the UPS is doing.
After you are done, clean up by disabling the upsc administrative privileges:
UPS Variables and Commands
In some cases you may wish to modify variables on the actual UPS such as the Low Charge/LOWBATTERY setting. This requires the use of the upsrw command and UPS administrative privileges.
You may also want to control the UPS directly from the command line by issuing UPS commands. This requires use of the upscmd command and UPS administrative privileges.
UPS Administrative Privileges
In order to be able to use upsrw and upscmd it is necessary to have a suitable additional user defined in the upsd.users configuration file.
In order to create a suitable user we will use SME Servers templating system and configuration database. This is based on an original forum thread[1].
First we need to create a suitable custom template directory
mkdir -p /etc/e-smith/templates-custom/etc/ups/upsd.users cd /etc/e-smith/templates-custom/etc/ups/upsd.users
Create and edit a new file called 'admin' with the following content:
{
# create admin user for upsd to allow setting of
# UPS parameters via upsrw
$OUT .= "";
return unless (($nut{AdminUser} || 'disabled') eq 'enabled');
return unless (($nut{AdminPass} || '') ne '');
$OUT .= "\n";
$OUT .= " [admin]\n";
$OUT .= " password = $nut{AdminPass}\n";
if ( ($nut{Master} || 'yes') ne 'no') {
$OUT .= " allowfrom = localhost\n";
} else {
$OUT .= " allowfrom = localhost localnet\n";
}
$OUT .= " actions = set\n";
$OUT .= " instcmds = all\n";
}
Create two new database properties for nut
config setprop nut AdminUser enabled (This enables the creation of the user in the template above) config setprop nut AdminPass admin (This sets a password for the admin user. Set to whatever you want)
Now, to get upsd to recognise the new user with the required administrative privileges we expand the template and reload the upsd configuration
/sbin/e-smith/expand-template /etc/ups/upsd.users /usr/sbin/upsd -c reload
Setting UPS Variables
In order to set UPS variables it is necessary to have enabled a user with administrative privileges as above first.
In the examples below, it is assumed your UPS name is UPS, that it is local, that the administrative user is admin and password admin. You can verify your UPS name via:
upsc -l
To view a complete list of the UPS variables, both informational and modifiable
upsc UPS
To determine the modifiable variables for your UPS, their current settings and their available setting values execute the command:
upsrw UPS
You can now modify the variables you wish using a command similar to the following (Note the order of the arguments is important, and you may need quotes around the value being set, "20"):
upsrw -s battery.charge.low=20 -u admin -p admin UPS
Where the value after -s should be one of the parameters identified by the upsrw ups command. You can of course verify your changes using
upsrw UPS
or
upsc UPS
After you are done, clean up by disabling the upsd administrative user admin:
More information on upsrw can be found at:
- Manual page: man upsrw
Issuing UPS Commands
In order to issue UPS commands it is necessary to have enabled a user with administrative privileges as above first.
In the examples below, it is assumed your UPS name is UPS, that it is local, that the administrative user is admin and password admin. You can verify your UPS name via:
upsc -l
To view a complete list of available commands for your UPS:
upscmd -l UPS
You can now issue a command to the UPS with similar to the following:
upscmd -u admin -p admin UPS test.battery.start
Where the command test.battery.start is a valid command for your UPS as previously determined by upscmd -l UPS. Depending upon the command issued you may get broadcast messages and emails relating to and confirming what the UPS is doing.
After you are done, clean up by disabling the upsd administrative user admin:
an example to update you battery date upon changing it. (use your own password)
upsrw -s battery.mfr.date=2020/08/31 -u admin -p admin UPS
Scheduling Events
Shutdown Time Delay Example
By default NUT will issue a shutdown command as soon as it receives a low battery event from the UPS. There may be instances and installation configurations that require a shutdown sooner, or other events with timed or schedules outcomes. See the man pages etc for further info and example situations.
In essence the upsmon program monitors the relevant UPS and for each NOTIFYFLAG event in upsmon.conf takes immediate action as defined. In order to delay or schedule any actions, the events need to be passed to upssched which can set timers and schedule events.
The following changes to standard SME Server NUT configuration will shut down the server a specified time after receiving the "on battery" signal (the example given is for 2 minutes). It assumes you already have an enabled and working NUT configuration and UPS
To create a timed shutdown before the BATTLOW signal is received, it is necessary to configure upssched and have a script handle the UPS events (upsmon cannot do this).
First we need to create a new custom template directory:
mkdir -p /etc/e-smith/templates-custom/etc/ups/upsmon.conf cd /etc/e-smith/templates-custom/etc/ups/upsmon.conf
Create and edit a new file called 'NOTIFYCMD' with the following content:
NOTIFYCMD /usr/sbin/upssched
Expand the template:
/sbin/e-smith/expand-template /etc/ups/upsmon.conf
Now create another a custom template directory
mkdir -p /etc/e-smith/templates-custom/etc/ups/upssched.conf cd /etc/e-smith/templates-custom/etc/ups/upssched.conf
Create and edit a new file called '01CONFIG' with the following content:
CMDSCRIPT /sbin/e-smith/nutUPS.cmd PIPEFN /tmp/upspipe LOCKFN /tmp/upslock AT COMMBAD * EXECUTE commbad AT COMMOK * EXECUTE commok AT NOCOMM * EXECUTE nocomm AT ONBATT * EXECUTE powerout AT ONBATT * START-TIMER shutdownnow 120 AT LOWBATT * EXECUTE shutdowncritical AT ONLINE * CANCEL-TIMER shutdownnow AT ONLINE * EXECUTE powerup
In the above set the line AT ONBATT * START-TIMER shutdownnow 120 to how many seconds after ONBATT signal you want to shut down
Expand the template:
/sbin/e-smith/expand-template /etc/ups/upssched.conf
Create and edit a new script file at:
/sbin/e-smith/nutUPS.cmd
Add the following content:
#! /bin/sh
case $1 in
commbad)
/bin/echo "UPS communications failure on `date`." | /bin/mail -s"UPS communications LOST" admin
/usr/bin/wall "UPS communications failure."
;;
commok)
/bin/echo "UPS communications restored on `date`." | /bin/mail -s"UPS communications restored" admin
/usr/bin/wall "UPS communications restored."
;;
nocomm)
/bin/echo "UPS communications cannot be established on `date`." | /bin/mail -s"UPS uncontactable" admin
/usr/bin/wall "UPS communications cannot be established."
;;
powerout)
/bin/echo "Power failure on `date`." | /bin/mail -s"UPS on battery" admin
/usr/bin/wall "UPS on battery. Shutdown in 60 seconds...."
;;
shutdownnow)
/bin/echo "UPS has been on battery for 60 seconds. Starting orderly shutdown on `date`." | /bin/mail -s"UPS on battery for 60 seconds" admin
/usr/bin/wall "UPS has been on battery for 60 seconds. Shutting down NOW!!!!"
/usr/bin/sudo /sbin/e-smith/signal-event halt
;;
shutdowncritical)
/bin/echo "UPS battery level CRITICAL. Starting EMERGENCY shutdown on `date`." | /bin/mail -s"UPS battery CRITICAL" admin
/usr/bin/wall "UPS battery level CRITICAL. Shutting down NOW!!!!"
/usr/bin/sudo /sbin/e-smith/signal-event halt
;;
powerup)
/bin/echo "Power restored on `date`." | /bin/mail -s"UPS on line" admin
/usr/bin/wall "UPS on line. Shutdown aborted."
;;
*)
/bin/echo "Unrecognized command: $1"
;;
esac
Now make it executable by nut user
chmod 754 /sbin/e-smith/nutUPS.cmd chown root:nut /sbin/e-smith/nutUPS.cmd
Nut requires to use sudo for this process to work, so sudo needs configuring to enable the user nut. By default the /etc/sudoers file is not part of the SME Server template system. To workaround this create a custom template directory:
mkdir -p /etc/e-smith/templates-custom/etc/sudoers cd /etc/e-smith/templates-custom/etc/sudoers
To preserve the content of the orginal /etc/sudoers file copy that into the custom template directory:
cp /etc/sudoers 10sudoers
Create and edit a new file called '30nut' with the following content:
nut ALL=NOPASSWD: ALL
Then run:
/sbin/e-smith/expand-template /etc/sudoers
Finally to complete the process:
signal-event post-upgrade signal-event reboot
While testing with the SMEServer v9.1 (circa March 2016), the above nutUPS.cmd script with entries in 01CONFIG template fails due to lack of permissions at the shutdownnow case at:
/usr/bin/sudo /sbin/e-smith/signal-event halt
Tweaking the /etc/sudoers did not mitigate it.
The error in the /var/log/messages is:
Mar 14 13:22:16 svr01 upssched[3507]: Timer daemon started Mar 14 13:22:16 svr01 upssched[3507]: New timer: shutdownnow (120 seconds) Mar 14 13:25:16 svr01 upssched[3507]: Event: shutdownnow Mar 14 13:25:16 svr01 wall[3539]: wall: user nut broadcasted 1 lines (70 chars) Mar 14 13:25:16 svr01 upssched[3507]: exec_cmd(/sbin/e-smith/nutUPS.cmd shutdownnow) returned 1
However, the nut user has the necessary shutdown permissions:
/usr/bin/sudo -u nut /usr/bin/sudo /sbin/e-smith/signal-event halt
Configure Nut-cgi Monitor Scripts
The nut-cgi rpm contains scripts that can be run via the webserver to monitor the UPS(s).
Download and install
You have to enable the epel repository:
yum install smeserver-extrarepositories-epel -y
then install nut-cgi:
yum install --enablerepo=epel nut-cgi
then configure it the SME way: Edit file /etc/ups/hosts.conf and add.
mkdir -p /etc/e-smith/templates-custom/etc/ups/hosts.conf echo 'MONITOR UPS@localhost "local UPS"' >/etc/e-smith/templates-custom/etc/ups/hosts.conf/10localhost expand-template /etc/ups/hosts.conf
Httpd template
mkdir -p /etc/e-smith/templates-custom/etc/httpd/conf/httpd.conf cd /etc/e-smith/templates-custom/etc/httpd/conf/httpd.conf
Now edit and create a new file 92nutupscmon with the following content
{
$OUT = "";
my $allow = 'all';
my $pass = '0';
my $satisfy = 'all';
my $name = $nut{'Name'} || 'NUT UPS Daemon Monitoring';
my $PublicAccess = $nut{'PublicAccess'} || "local";
for ('exit-if-none')
{
if ($PublicAccess eq 'none')
{
next;
}
elsif ($PublicAccess eq 'local')
{
$allow = "ip $localAccess";
$pass = 0;
$satisfy = 'All';
}
elsif ($PublicAccess eq 'local-pw')
{
$allow = "ip $localAccess";
$pass = 1;
$satisfy = 'All';
}
elsif ($PublicAccess eq 'global')
{
$allow = 'all granted';
$pass = 0;
$satisfy = 'All';
}
elsif ($PublicAccess eq 'global-pw')
{
$allow = 'all granted';
$pass = 1;
$satisfy = 'All';
}
elsif ($PublicAccess eq 'global-pw-remote')
{
$allow = "ip $localAccess";
$pass = 1;
$satisfy = 'Any';
}
$OUT .= "#------------------------------------------------------------\n";
$OUT .= "# nut multimon - $name\n";
$OUT .= "#------------------------------------------------------------\n";
{
if ((exists $nut{'URL'}) && ($nut{'URL'} ne '')) {
$OUT .= "Alias /$nut{'URL'} /var/www/nut-cgi-bin\n";
}
}
$OUT .= "Alias /nut /var/www/nut-cgi-bin\n";
$OUT .= "\n";
$OUT .= "<Directory /var/www/nut-cgi-bin>\n";
$OUT .= " DirectoryIndex upsstats.cgi\n";
$OUT .= " Options +ExecCGI\n";
$OUT .= " <Require$satisfy>\n" if ($pass);
$OUT .= " Require $allow\n";
if ($pass)
{
$OUT .= " AuthName $name\n";
$OUT .= " AuthType Basic\n";
$OUT .= " AuthExternal pwauth\n";
$OUT .= " require valid-user\n";
$OUT .= " </Require$satisfy>\n";
}
$OUT .= "</Directory>\n";
}
}
Configure databases and expand the template
config setprop nut PublicAccess local /sbin/e-smith/expand-template /etc/httpd/conf/httpd.conf
Restart the web server
systemctl restart httpd-e-smith
You have to enable the epel repositories.
yum install --enablerepo=epel nut-cgi
Edit file /etc/ups/hosts.conf and add.
MONITOR UPS@localhost "local UPS"
The nut-cgi rpm contains three cgi scripts. The rpm does not install them correctly for SME however so the following modifications are needed.
mkdir -p /opt/nut-cgi-bin chown root:www /opt/nut-cgi-bin mv /var/www/nut-cgi-bin/upsstats.cgi /opt/nut-cgi-bin mv /var/www/nut-cgi-bin/upsset.cgi /opt/nut-cgi-bin mv /var/www/nut-cgi-bin/upsimage.cgi /opt/nut-cgi-bin chown root:www /opt/nut-cgi-bin/* chmod 750 /opt/nut-cgi-bin/* mkdir -p /etc/e-smith/templates-custom/etc/httpd/conf/httpd.conf cd /etc/e-smith/templates-custom/etc/httpd/conf/httpd.conf
Now edit and create a new file 92nutupscmon with the following content
{
$OUT = "";
my $allow = 'all granted';
my $pass = '0';
my $satisfy = 'All';
my $name = $nut{'Name'} || 'NUT UPS Daemon Monitoring';
for ('exit-if-none')
{
if ($nut{'PublicAccess'})
{
if ($nut{'PublicAccess'} eq 'none')
{
next;
}
elsif ($nut{'PublicAccess'} eq 'local')
{
$allow = $localAccess;
$pass = 0;
$satisfy = 'all';
}
elsif ($nut{'PublicAccess'} eq 'local-pw')
{
$allow = $localAccess;
$pass = 1;
$satisfy = 'all';
}
elsif ($nut{'PublicAccess'} eq 'global')
{
$allow = 'all';
$pass = 0;
$satisfy = 'all';
}
elsif ($nut{'PublicAccess'} eq 'global-pw')
{
$allow = 'all';
$pass = 1;
$satisfy = 'all';
}
elsif ($nut{'PublicAccess'} eq 'global-pw-remote')
{
$allow = $localAccess;
$pass = 1;
$satisfy = 'any';
}
}
$OUT .= "#------------------------------------------------------------\n";
$OUT .= "# nut multimon - $name\n";
$OUT .= "#------------------------------------------------------------\n";
{
if ((exists $nut{'URL'}) && ($nut{'URL'} ne '')) {
$OUT .= "Alias /$nut{'URL'} /opt/nut-cgi-bin\n";
}
}
$OUT .= "Alias /nut /opt/nut-cgi-bin\n";
$OUT .= "\n";
$OUT .= "<Directory /opt/nut-cgi-bin>\n";
$OUT .= " DirectoryIndex upsstats.cgi\n";
$OUT .= " Options +ExecCGI\n";
$OUT .= " order deny,allow\n";
$OUT .= " deny from all\n";
$OUT .= " allow from $allow\n";
if ($pass)
{
$OUT .= " AuthName $name\n";
$OUT .= " AuthType Basic\n";
$OUT .= " AuthExternal pwauth\n";
$OUT .= " require valid-user\n";
$OUT .= " Satisfy $satisfy\n";
}
$OUT .= "</Directory>\n";
}
}
Configure databases and expand the template
config setprop nut PublicAccess local /sbin/e-smith/expand-template /etc/httpd/conf/httpd.conf
Restart the web server
sv t httpd-e-smith
Usage of Nut-cgi Scripts
Now go to http://yourdomain.tld/nut to see the statistics and information for the UPS at localhost.
By editing /etc/ups/hosts.conf and adding additional network UPS details, nut-cgi can be used to monitor more than one UPS. By the modification above, only the localhost is monitored.
Additional Information
There are template fragments in /etc/e-smith/templates/etc/ups that control the config files located in /etc/ups. The default settings should be OK for most situations. The /etc/nut.conf file must be manually edited like mode=standalone as the templates do not touch this file. In this case it would be:
sed -e 's/^MODE.*/MODE=standalone/' -i /etc/ups/nut.conf
By default, NUT is configured for a USB connected UPS in Master mode, but is disabled. When enabled, NUT will monitor the UPS and take various actions when certain notifications are received. This is controlled by the /etc/ups/upsmon.conf file which among other things lists the notifications and the actions to be taken for each. For example an On Battery event is captured by the NOTIFYFLAG ONBATT entry and the following SYSLOG+WALL+EXEC command string. This string tells upsmon to write the event to the System Log, broadcast a message to all users via Wall, and execute the command denoted by the NOTIFYCMD entry.
SME Server sets the NOTIFYCMD to /sbin/e-smith/nutUPS.notify, and this executable file simply sends an email to the SME admin user with a notification of the event.
Apart from the various events that the UPS and upsmon may notify via the NOTIFYFLAGS a Low Battery event will automatically and immediately cause upsmon to issue the SHUTDOWNCMD as defined in upsmon.conf (signal-event halt) and set a flag POWERDOWNFLAG so it knows on future restart that it is a UPS recovery.
For information on configuration parameters:
man ups.conf man upsd.conf man upsd.users man upsmon.conf man upssched.conf
For general information:
man upsd man nutupsdrv
Timeout Issues
If you have comms problems like this you can add a custom timeout:
"USBDEVFS_CONTROL failed cmd blazer_usb rqt 33 rq 9 len 8 ret -110"
Add a new config item. The default is 2
config setprop nut pollInterval 4
Modify the template
mkdir -p /etc/e-smith/templates-custom/etc/ups/ups.conf cp /etc/e-smith/templates/etc/ups/ups.conf/UPS /etc/e-smith/templates-custom/etc/ups/ups.conf/UPS nano /etc/e-smith/templates-custom/etc/ups/ups.conf/UPS
Add the bits between the # comments
{
my $model = $nut{Model} || "usbhid-ups";
my $device = $nut{Device} || "/var/lib/ups/hiddev0";
my $type = $nut{Type};
my $mfr = $nut{mfr};
my $mdl = $nut{mdl};
# Add this
my $poll = $nut{pollInterval} || '2';
if ($poll ne '2') {
$OUT .= "pollinterval = $poll\n";
}
# ends here
$OUT .= "[UPS]\n"; $OUT .= "\tdriver = $model\n";
expand-template /etc/ups/ups.conf cat /etc/ups/ups.conf
You should see something like this:
# Copyright (C) 1999-2006 Mitel Networks Corporation #------------------------------------------------------------ pollinterval = 4 [UPS]
Restart nut
service nut restart
Now check to see the correct timeout:
upsc UPS | grep driver.parameter.pollinterval
driver.parameter.pollinterval: 4
To reset either delete the key, or set it to the default of 2
Further reading
The NUT website is here: NUT
From the above references you can glean which configuration setting does what function, etc.
If you want to modify the operation of NUT from the standard configuration, then you should generally modify the NUT config files by creating custom templates, expanding the templates and restarting service. This will ensure modifications survive a future reboot or reconfiguration.
An example of doing this can be found in the forum [2] and in the section above for UPS Administrative Privileges
See also Known Problem - Restarting Nut
Documentation
Nut is a Software well documented, you can find the TOC here and with an overview
