Backup of ESXi Virtual Machines using Affa

	Skill level: Advanced
	The instructions on this page may require deviations from standard procedures. A good understanding of linux and Koozali SME Server is recommended.

Introduction

As of version 2, Affa supports hot backing up virtual machines running on the VMWare ESXi server. It uses the VMware Infrastructure Perl Toolkit to communicate with the EXSi and rsync over ssh to transfer the data. Before the backup starts, the state of the running VM is freezed by creating a snapshot of all its disks. After the freezed virtual disk files were backed up, the snapshot is deleted and the config points to the just backed up disks again. Then, as a last step the config files are backed up.

A restore of a VM can be done by simply copying back all archived files to the original location on the ESXi host. It is also possible to copy the files to a different directory (or to another ESXi server) and add the vmx file to the inventory.

	Note:
	This document is applicable to ESX3i with an USB boot device. It will most likely not work with other type boot devices

	Warning:
	As Affa Version 2 is in a BETA state, errors in design and/or implementation cannot be completely eliminated. Therefore take precautions to avoid negative impacts to your system. In particular do not use it on production systems.

Preparing the Affa Server

Install the VMware Infrastructure (VI) Perl Toolkit

Download the VI Perl Toolkit tarball from the VMWare web site: http://www.vmware.com/support/developer/viperltoolkit/

Login as root and run:

/usr/bin/yum install openssl-devel
/usr/bin/yum --enable=dag install perl-XML-SAX
tar xzf VMware-VIPerl-1.6.0-104313.i386.tar.gz
cd vmware-viperl-distrib
./vmware-install.pl

Ignore this warning: The following Perl modules were found on the system but may be too old to work with VIPerl: URI XML::NamespaceSupport

Install Affa Version 2 beta

Install the latest Affa 2.x beta version. Download the RPM from http://mirror.contribs.org/smeserver/contribs/michaelw/sme7/Affa2

/usr/bin/yum --enable=smecontribs localinstall smeserver-affa-2.0.0-beta*.noarch.rpm

Preparing the ESXi Host for use with Affa

To make the ESXi server ready to cooperate with Affa you must install the rsync program, enable the ssh service, configure passwordless ssh login and add a user for communication using the VMware Infrastructure (VI) Perl Toolkit.

Adding an ESXi User with restricted Permissions

Run the Virtual Infrastructure Client and logon to the ESXi host.

Adding Affa role

Switch to the Administration module and add a new role with permissions to create and delete snapshots

Adding Affa user

Switch back to the Inventory module and add a new user with password:

Assigning permissions

In the Permission Tab assign the new role to the new user.

Configuring SSH and RSYNC on the ESX3i Host

On ESXi the SSH service Dropbear is installed but disabled. To use rsync the SSH service must be enabled and the rsync program must be installed. To enable passwordless login a .ssh directory for storing the keys must be created.

A script is provided that does this: To set up ESXi for use with Affa we must:

• enable SSH service by configuring inetd.conf and restarting the inetd service
• install rsync (statically linked binary)
• create a /root home directory with a .ssh sub directory to store the public keys for password-less login
• link the .ssh directory to the non-volatile USB device
• add a command to /etc/rc.local that executes all the steps above at boot time

# enable ssh service
sed -ie 's/^#\(ssh.*\)/\1/' /etc/inetd.conf
# reload inetd configuration
kill -HUP `ps | grep inetd | sed -e 's/ .*//'`

# install rsync 3.0.4 statically linked
cp -a /bootbank/bexi/rsync-static /bin/rsync

# root home dir for storing public keys
mkdir -p /bootbank/bexi/root/.ssh
touch /bootbank/bexi/root/.ssh/authorized_keys
touch /bootbank/bexi/root/.ssh/known_hosts

# link .ssh dir to non-volatile USB location
mkdir -p /root
ln -fs /bootbank/bexi/root/.ssh /root/

# set new home dir for user root
sed -ie 's#^\(root:.*\)\(:/:\)\(.*\)#\1:/root:\3#' /etc/passwd

# add execution of this script to rc.local
grep -v "#BEXI$" < /etc/rc.local > /etc/rc.local.affa; mv -f /etc/rc.local.affa /etc/rc.local
echo "test -f /bootbank/bexi/affa-setup.sh && /bootbank/bexi/affa-setup.sh #BEXI" >> /etc/rc.local
echo "test ! -d /root && sed -ie 's#^\(root:.*\)\(:/root:\)\(.*\)#\1:/:\3#' /etc/passwd  #BEXI" >> /etc/rc.local

Download and install the skript

On the ESXi Server console hit Alt-F1 to get the service shell. Now blind-type the word unsupported to unlock the shell.

Login with the root password.

Download the tarball. The tarball contains all binaries and the script.

cd /bootbank
wget http://mirror.contribs.org/smeserver/contribs/michaelw/sme7/Affa2/affa-esxi-setup-02.tgz 

Verify the download

 wget http://mirror.contribs.org/smeserver/contribs/michaelw/sme7/Affa2/affa-esxi-setup-02.tgz.md5sum 
 md5sum -c affa-esxi-setup-01.tgz.md5sum

Unpack it

tar xzf affa-esxi-setup-02.tgz 
rm affa-esxi-setup-02.tgz* 

and run the script

./bexi/affa-setup.sh

Now you can ssh login and use rsync.

Setting up an Affa job

The following assumes, that you are already familiar with configuring Affa and only focus on the ESXi specific parts.

Assume you want to backup the virtual machine named 'myvm' on ESXi server with IP 10.200.48.5.

1. log into the 'affabox' and copy the config helper script

cp -a /usr/lib/affa/jobconfig-esxi-sample.pl /root/esxi-myvm-job.pl

2. edit /root/esxi-myvm-job.pl and set

my $jobname='esxi-myvm';

and

'remoteHostName‘=>'10.200.48.5',

3. tell Affa that this job backups a ESXi virtual machine

'ESXi' => 'yes',

4. set the VM name

'ESXiVMName' => 'myvm',

5. set the username and password (this is the ESXi User with restricted permissions created above)

'ESXiUsername' => 'affa',
'ESXiPassword' => 'secret',

6. save the script, then run it

/root/esxi-myvm-job.pl

7. send the public key

affa --send-key esxi-myvm

8. run the job manually

affa --run esxi-myvm

When the Affa job starts, you can watch the snapshot create task in the Virtual Infrastructure Client.

The name of the snaphot starts with "BEXI-". Do not delete it or revert to it while Affa is running.

Uninstall

SSH login as root on the ESXi host and run these commands carefully:

grep -v "#BEXI" < /etc/rc.local >/etc/rc.local.affa; mv -f /etc/rc.local.affa /etc/rc.local
sed -e 's#^\(root:.*\)\(:/root:\)\(.*\)#\1:/:\3#' < /etc/passwd > /etc/passwd.affa; mv -f /etc/passwd.affa /etc/passwd
sed -e 's/^\(ssh.*\)/#\1/' < /etc/inetd.conf > /etc/inetd.conf.affa; mv -f /etc/inetd.conf.affa /etc/inetd.conf
kill -HUP `ps | grep inetd | sed -e 's/ .*//'`
rm -rf /bin/rsync /root /bootbank/bexi
tar -C / -xzf /bootbank/environ.tgz sbin/dropbearmulti

Addtional Information

How to make the statically linked Rsync Binary

1. download the source from http://rsync.samba.org/

2. unpack the tarball

tar xzf rsync-3.0.4.tar.gz
cd rsync-3.0.4

3. build the statically linked binary

make CFLAGS="-static" EXEEXT="-static"
strip rsync-static