Difference between revisions of "Prosody"
| Line 27: | Line 27: | ||
admins = {"admin@yourdomain.com"} | admins = {"admin@yourdomain.com"} | ||
allow_registration = true | allow_registration = true | ||
| − | VirtualHost "localhost | + | VirtualHost "localhost" |
VirtualHost "yourdomain.com" | VirtualHost "yourdomain.com" | ||
enabled = true | enabled = true | ||
| Line 35: | Line 35: | ||
Any XMPP client can register itself on your server or you can use LDAP authentication so that your SME Server users automatically have access to your XMPP server. | Any XMPP client can register itself on your server or you can use LDAP authentication so that your SME Server users automatically have access to your XMPP server. | ||
| − | Register yourself as "admin" to be an administrator as defined in the configuration file. | + | Register yourself as "admin" to be an administrator as defined in the configuration file. |
| − | |||
===Modules configuration=== | ===Modules configuration=== | ||
Revision as of 04:25, 27 January 2015
About
"Prosody is a modern XMPP communication server (aka Jabber). It aims to be easy to set up and configure, and efficient with system resources. Additionally, for developers it aims to be easy to extend and give a flexible system on which to rapidly develop added functionality, or prototype new protocols."
Installation
These instructions are for SME Server 9.0 64-bit only.
Prosody is available from the epel repository, so you have to enable the epel repository. Epel only holds the 0.8.x series of Prosody, to install or upgrade to the latest 9.x series of Prosody see below instructions. After enabling the epel repository, prosody can be installed with:
yum install prosody lua-ldap --enablerepo=epel
Configuration
Adding service and open ports
To automatically start Prosody at boot and configure the ports:
ln -s /etc/rc.d/init.d/e-smith-service /etc/rc7.d/S99prosody config set prosody service config setprop prosody status enabled access private TCPPort 5222 UDPport 5222 signal-event remoteaccess-update
You can toggle the access property to enable public/private access.
Configuration file
Prosody's configuration file is located at:
/etc/prosody/prosody.cfg.lua
The basic settings you have to change to run your prosody server on your domain (replace "example.com" with "yourdomain.com"):
admins = {"admin@yourdomain.com"}
allow_registration = true
VirtualHost "localhost"
VirtualHost "yourdomain.com"
enabled = true
You can now start prosody by entering:
service prosody start
Any XMPP client can register itself on your server or you can use LDAP authentication so that your SME Server users automatically have access to your XMPP server.
Register yourself as "admin" to be an administrator as defined in the configuration file.
Modules configuration
TBA
LDAP configuration
TBA
Prosody version 0.9.x
TBA
cd /root wget http://ftpsrv01.networklab.ca/centos/6/RPMS/x86_64/prosody-0.9.4-2.el6.x86_64.rpm wget http://ftpsrv01.networklab.ca/centos/6/RPMS/x86_64/lua-bitop-1.0.2-1.el6.x86_64.rpm wget http://ftpsrv01.networklab.ca/centos/6/RPMS/x86_64/lua-sec-0.4.1-6.el6.x86_64.rpm wget http://ftpsrv01.networklab.ca/centos/6/RPMS/x86_64/luajit-2.0.2-9.el6.x86_64.rpm wget http://ftpsrv01.networklab.ca/centos/6/RPMS/x86_64/lua-zlib-0.2-1.el6.x86_64.rpm yum localinstall *.rpm --enablerepo=epel
Documentation
For further and detailed configuration of the Prosody server and services, please see the Prosody documentation
