Difference between revisions of "IAXModem with Sail and HylaFax"
| Line 90: | Line 90: | ||
# chkconfig: 2345 95 05 | # chkconfig: 2345 95 05 | ||
# description: IAXModem for asterisk <-> Hylafax gateway | # description: IAXModem for asterisk <-> Hylafax gateway | ||
| − | + | ||
# Source function library. | # Source function library. | ||
. /etc/rc.d/init.d/functions | . /etc/rc.d/init.d/functions | ||
| − | + | ||
[ -f /usr/local/sbin/iaxmodem ] || exit 0 | [ -f /usr/local/sbin/iaxmodem ] || exit 0 | ||
| − | + | ||
prog="IAXmodem" | prog="IAXmodem" | ||
| − | + | ||
start() { | start() { | ||
echo -n $"Starting $prog: " | echo -n $"Starting $prog: " | ||
| Line 105: | Line 105: | ||
return $RETVAL | return $RETVAL | ||
} | } | ||
| − | + | ||
stop() { | stop() { | ||
if test "x`pidof iaxmodem`" != x; then | if test "x`pidof iaxmodem`" != x; then | ||
| Line 115: | Line 115: | ||
return $RETVAL | return $RETVAL | ||
} | } | ||
| + | |||
reload() { | reload() { | ||
if test "x`pidof iaxmodem`" != x; then | if test "x`pidof iaxmodem`" != x; then | ||
| Line 121: | Line 122: | ||
fi | fi | ||
} | } | ||
| − | + | ||
case "$1" in | case "$1" in | ||
start) | start) | ||
| Line 145: | Line 146: | ||
fi | fi | ||
;; | ;; | ||
| − | + | ||
*) | *) | ||
echo $"Usage: $0 {start|stop|reload|restart|condrestart|status}" | echo $"Usage: $0 {start|stop|reload|restart|condrestart|status}" | ||
exit 1 | exit 1 | ||
| − | + | ||
esac | esac | ||
| − | + | ||
exit $RETVAL | exit $RETVAL | ||
Revision as of 22:16, 15 January 2010
Introduction
This Howto is aimed at the installation of IAXModem in conjunction with SAIL/asterisk and Hylafax in order to provide a fax over VOIP solution. It is based on information from various forum posts including:
http://forums.contribs.org/index.php/topic,39258.msg179460.html
http://forums.contribs.org/index.php/topic,41256.msg219493.html
Sail and Asterisk Setup
General
In Global Settings
- Make sure that 'Late Termination' is set to No.
- Make sure that the 'Autosense FAX Extension' is set to a number you want to use for the Fax. You will need this number later.
- The 'Fax Delay' setting defaults to 2 seconds. You may need to adjust this later to make sure faxes get detected before asterisk attempts to terminate somewhere other than the FAX.
For each of the Trunks under Trunklines that you want to be able to detect incoming Faxes on
- Make sure that the 'Fax' detection tick box is ticked
Fax Extension
Create a new Extension with the same number as set in the 'Autosense FAX Extension' as above - or vice versa. The 'Device' should be IAXModem.
Once created check the stanza generally conforms to the following and change as necessary:
[2000] type=friend username=FaxModem secret=asterisk host=dynamic qualify=3000 context=internal callerid="Faxmodem" <2000> disallow=all allow=slin
IAXModem
Installation
Download the iaxmodem rpm from Aelintra and install
wget http://sarkpbx.com/sail/iaxmodem/iaxmodem-1.0.0-1.noarch.rpm yum localinstall iaxmodem-1.0.0-1.noarch.rpm
Configuration
Check and edit /etc/iaxmodem/ttyIAX0 as necessary:
device /dev/ttyIAX owner uucp:uucp mode 660 port 4570 refresh 60 server 127.0.0.1 peername 2000 secret asterisk cidname YourCompany cidnumber 0123456789 codec slinear
Check and Run
Check the modem registers with Sail and Asterisk
/usr/local/sbin/iaxmodem ttyIAX
should give an output similar to
Modem started Setting device = '/dev/ttyIAX' Setting owner = 'uucp:uucp' Setting mode = '660' Setting port = 4570 Setting refresh = 60 Setting server = '127.0.0.1' Setting peername = '2000' Setting secret = 'asterisk' Setting cidname = 'YourCompany' Setting cidnumber = '0123456789' Setting codec = slinear Opened pty, slave device: /dev/pts/0 Created /dev/ttyIAX symbolic link Registration completed successfully.
and in an asterisk CLI
--Registered IAX2 '2000' (AUTHENTICATED) at 127.0.0.1:4570
Now
db configuration set iaxmodem service status enabled /etc/rc.d/rc7.d/S93iaxmodem start
iaxmodem
The following is the code for the /etc/rc.d/init.d/iaxmodem script from the current iaxmodem-1.2.0.tar.gz source.
#!/bin/sh
# Startup script for iaxmodem
#
# chkconfig: 2345 95 05
# description: IAXModem for asterisk <-> Hylafax gateway
# Source function library.
. /etc/rc.d/init.d/functions
[ -f /usr/local/sbin/iaxmodem ] || exit 0
prog="IAXmodem"
start() {
echo -n $"Starting $prog: "
daemon /usr/local/sbin/iaxmodem
RETVAL=$?
echo
return $RETVAL
}
stop() {
if test "x`pidof iaxmodem`" != x; then
echo -n $"Stopping $prog: "
killproc iaxmodem
echo
fi
RETVAL=$?
return $RETVAL
}
reload() {
if test "x`pidof iaxmodem`" != x; then
echo $"Reloading $prog"
kill -HUP `head -1 /var/run/iaxmodem.pid`
fi
}
case "$1" in
start)
start
;;
stop)
stop
;;
status)
status iaxmodem
;;
reload)
reload
;;
restart)
stop
start
;;
condrestart)
if test "x`pidof iaxmodem`" != x; then
stop
start
fi
;;
*)
echo $"Usage: $0 {start|stop|reload|restart|condrestart|status}"
exit 1
esac
exit $RETVAL
