IAXModem with Sail and HylaFax

	Incomplete:
	This article or section needs to be expanded. Please help to fill the gaps or discuss the issue on the talk page

Introduction

This Howto is aimed at the installation of IAXModem in conjunction with SAIL/asterisk and Hylafax in order to provide a fax over VOIP solution. It is based on information from various forum posts including:

http://forums.contribs.org/index.php/topic,39258.msg179460.html

http://forums.contribs.org/index.php/topic,41256.msg219493.html

	Note:
	This has only been tested with Asterisk 1.4.25.1-78, Sail 2.4.1-2 and the Hylafax Contrib from Dungog smeserver-hylafax-0.9.6 with hylafax-4.4.4-1 No other asterisk implementations have been used or tested. It is assumed that you have a working Sail/asterisk installation

Sail and Asterisk Setup

General

In Global Settings

• Make sure that 'Late Termination' is set to No.
• Make sure that the 'Autosense FAX Extension' is set to a number you want to use for the Fax. You will need this number later.
• The 'Fax Delay' setting defaults to 2 seconds. You may need to adjust this later to make sure faxes get detected before asterisk attempts to terminate somewhere other than the FAX.

For each of the Trunks under Trunklines that you want to be able to detect incoming Faxes on

• Make sure that the 'Fax' detection tick box is ticked

Fax Extension

Create a new Extension with the same number as set in the 'Autosense FAX Extension' as above - or vice versa. The 'Device' should be IAXModem.

	Note:
	We will assume an extension number of 2000, a password (secret) of asterisk and a Display Name of FaxModem

Once created check the stanza generally conforms to the following and change as necessary:

[2000]
type=friend
username=FaxModem
secret=asterisk
host=dynamic
qualify=3000
context=internal
callerid="Faxmodem" <2000>
disallow=all
allow=slin

IAXModem

Installation

	Note:
	Sail installs /etc/rc.d/rc7.d/S93iaxmodem but does not install /etc/rc.d/init.d/iaxmodem

Download the iaxmodem rpm from Aelintra and install

wget http://sarkpbx.com/sail/iaxmodem/iaxmodem-1.0.0-1.noarch.rpm
yum localinstall iaxmodem-1.0.0-1.noarch.rpm

	Note:
	Current version of iaxmodem is 1.2 but there doesn't appear to a Centos 4 package for it anywhere

	Warning:
	This rpm does not install /etc/rc.d/init.d/iaxmodem so you will need to create one. A copy of the current version 1.2 code is reproduced at the end of this Howto. You may need to set the permissions and ownership chmod 766 iaxmodem chown root:root iaxmodem

Configuration

Check and edit /etc/iaxmodem/ttyIAX0 as necessary:

device          /dev/ttyIAX
owner           uucp:uucp
mode            660
port            4570
refresh         60
server          127.0.0.1
peername        2000
secret          asterisk
cidname         YourCompany
cidnumber       0123456789
codec           slinear

Check and Run

Check the modem registers with Sail and Asterisk

/usr/local/sbin/iaxmodem ttyIAX

should give an output similar to

Modem started
Setting device = '/dev/ttyIAX'
Setting owner = 'uucp:uucp'
Setting mode = '660'
Setting port = 4570
Setting refresh = 60
Setting server = '127.0.0.1'
Setting peername = '2000'
Setting secret = 'asterisk'
Setting cidname = 'YourCompany'
Setting cidnumber = '0123456789'
Setting codec = slinear
Opened pty, slave device: /dev/pts/0
Created /dev/ttyIAX symbolic link
Registration completed successfully.

and in an asterisk CLI

--Registered IAX2 '2000' (AUTHENTICATED) at 127.0.0.1:4570

Now

db configuration set iaxmodem service status enabled
/etc/rc.d/rc7.d/S93iaxmodem start

---