|
|
| (31 intermediate revisions by 3 users not shown) |
| Line 1: |
Line 1: |
| − | If you have fixed a request make here can you remove the comments so we can see what is still to be done
| |
| | | | |
| − | use templates not templates-custom
| |
| − |
| |
| − | create a smeserver-sane with the templates
| |
| − |
| |
| − | see http://wiki.contribs.org/HylaFax for an alternative to a full reconfig/reboot,
| |
| − | you just need to work out what needs to change
| |
| − |
| |
| − | good work so far, I'm dusting off my old scanner...
| |
| − |
| |
| − | :: Yes, I looked...
| |
| − | :: create a smeserver-sane with the templates: I do not have a lot of time at present
| |
| − | :: If I have a little of time...
| |
| − | :: I must finish the installation of mgetty / vgetty for SME before
| |
| − | :: I do not have a lot of place on my server and Shad still did not recover my src rpm.
| |
| − | :: Tomorrow I remove source of my server
| |
| − | :: [[User:Ecureuil|Ecureuil]]
| |
| − |
| |
| − | ----
| |
| − | Hi Cactus,
| |
| − |
| |
| − | I don't understand:
| |
| − | After succesfull of the required packages issue the following commands:
| |
| − |
| |
| − | signal-event post-upgrade
| |
| − | signal-event reboot
| |
| − | It isn't very good, it takes of 'CPU time '
| |
| − |
| |
| − | Ecureuil
| |
| − |
| |
| − | :What do you mean by that I do not understand your remark. Above commands are normal (required) steps after installing software using yum on the SME Server shell. - [[User:Cactus|Cactus]] 05:41, 4 April 2008 (MDT)
| |
| − |
| |
| − | == Stick to SME Server default syntax and naming conventions please ==
| |
| − |
| |
| − | Thank you for providing this Howto I think a lot of users will like this in the future, but I modified your English version and I noticed you have changed some items back. IMHO you should not have done so as I made changes to make things more conform to the SME Server naming conventions and you should have adapted them in your other translation(s) as well.
| |
| − |
| |
| − | A service normally is a daemon, hence the database record should be named saned (or sane) and not sane-port. On top of that I think it is also strange to call the group the server is configured to use to be saned, I therefore changed it to ''saneusers'' in the example to avoid confusion between users and the SANE daemon (which is normally referenced as saned).
| |
| − | - [[User:Cactus|Cactus]] 05:49, 4 April 2008 (MDT)
| |
| − | :: I don't speak english very good
| |
| − | :: Do not change anything without understanding and reading
| |
| − | :: View sane documentation: service = sane-port => grrrrrrrrrrrrrrr
| |
| − | :: http://www.sane-project.org/man/saned.8.html
| |
| − | :: http://penguin-breeder.org/sane/saned/
| |
| − | :: thank you
| |
| − | ::
| |
| − | :: Another problem:
| |
| − | :: If xinetd start, ' saned - d128 ' will not be able to work
| |
| − | :: I prefer the French version for it.
| |
| − | ::
| |
| − | :: for signal-event post-upgrade and signal-event reboot:
| |
| − | :: The post upgrade and the reboot process are only needed for smeserver
| |
| − | :: packages using the template system. As sane-backend nor xinetd are
| |
| − | :: smeserver specific, we don't need these (expensive !) steps.
| |
| − |
| |
| − | :: [[User:Ecureuil|Ecureuil]]
| |
