Difference between revisions of "SME Server:Documentation:Administration Manual:Chapter4"
| (4 intermediate revisions by the same user not shown) | |||
| Line 73: | Line 73: | ||
|- | |- | ||
! RAM | ! RAM | ||
| − | |4 GB | + | |At least 4 GB for all services, 8 GB supports most likely applications, more will be utilised if available |
|- | |- | ||
! Hard Drive | ! Hard Drive | ||
| Line 105: | Line 105: | ||
Do please note that the installer expects drives to be empty. Previously used drives should be wiped before being used for an install: this is sometimes tricky depending on which operating system was previously installed. Please see [[Raid#Reusing_Hard_Drives|Here]]. | Do please note that the installer expects drives to be empty. Previously used drives should be wiped before being used for an install: this is sometimes tricky depending on which operating system was previously installed. Please see [[Raid#Reusing_Hard_Drives|Here]]. | ||
| + | |||
| + | Do also note that selecting "Default Configuration" for storage from the text or GUI installer '''will''' override the SME defined automatic boot configuration for RAID! To recover from this a reboot will be necessary to reimplement the configuration before starting the installation. | ||
====4.4. Supported Ethernet or SCSI Adapters, or Tape Drives==== | ====4.4. Supported Ethernet or SCSI Adapters, or Tape Drives==== | ||
| Line 120: | Line 122: | ||
*etc. | *etc. | ||
| − | You can virtualize the | + | You can virtualize the Koozali SME Server on any computer when your processor has amd-v or vtx instructions. You need these instructions to use more than one core in the virtualised guest. Note: sometimes although supported, this has to be enabled in the BIOS. |
The amount of memory is a miminum of 2GB for the guest to be comfortable, and at least 4 GB with a lot of contribs installed; as always with memory more is usually better. | The amount of memory is a miminum of 2GB for the guest to be comfortable, and at least 4 GB with a lot of contribs installed; as always with memory more is usually better. | ||
For more detailed information on a virtualized SME Server, please see the [[Virtual_SME_Server]] page. | For more detailed information on a virtualized SME Server, please see the [[Virtual_SME_Server]] page. | ||
Latest revision as of 01:04, 24 April 2021
Hardware Requirements of the SME Server
The minimum hardware requirements of the SME Server are modest compared with other server software available today. However, because of its critical role in your office, selecting an appropriate host computer is important. While most desktop computers will run Koozali SME Server, server-grade computers are designed to run continuously and are a good choice for critical infrastructure. The hardware requirements of the host computer depend on such things as the number of users on your network, whether you plan to use the proxy server on the server, and the speed of your Internet connection.
When you consider the requirements, please be aware of the following notes:
- The server ships with the remote access services disabled by default. Enabling webmail will increase the resource requirements of your server, in particular the memory requirement. Other remote access services, such as SSH and VPNs, are also processor-intensive. You should consider a fast processor speed if you intend to make significant use of these services.
- The server should work with any x86-64 compatible CPU that can run Centos 7 for SME Server 10. Note that AMD desktop (as against server-grade) processors have not been tested by upstream, and a notice will be displayed accordingly: however many users are employing them satisfactorily at all levels of utilisation.
- The amount of available RAM is one of the most important considerations for server performance as it reduces the load on the disks. If a tradeoff is required, extra RAM will usually be more beneficial than a faster CPU.
- For a dedicated connection in server and gateway mode, your server requires two ethernet adapters (also called network adapters or network interface cards). For a dialup connection or server-only mode, one ethernet adapter is needed.
4.1. Minimum Hardware Requirements
The following information outlines what we consider the bare minimum system that will function as a basic file/print server and network gateway. Note that we do not believe such a system will provide satisfactory performance for features such as webmail, remote access via VPN, Virus and Spam Scanners, which are CPU intensive will not perform well on this platform. To utilize all the features of SME Server 10.0, please have a look at the 'Recommended' Hardware Requirements. Note: as Koozali SME Server is based on CentOS 7, the hardware requirements and support for CentOS 7 also apply here.
| Category | Specifications |
|---|---|
| Architecture | PCI-based x86-64 compatible processor |
| Processor speed | 1800 MHz |
| RAM | 2048 MB to install and run while disabling Clam AV, 4096 MB to effectively run all services including Clam AV, more memory is better. |
| Hard Drive | SATA/PATA or SCSI - at least 10/20GB (or 2 TB disk) |
| SCSI adapter | SCSI adapter must appear on the supported list (only necessary for SCSI systems) |
| Ethernet adapter(s) | The ethernet adapters installed on your server must appear on the supported list. |
| Modem (for dialup only) | Only modems that are Linux-compatible may be used. WinModems are not supported. |
| CD-ROM drive | SATA, ATAPI or SCSI |
| USB drive or key | USB2 is recommended for the install, as issues may arise with booting from USB3 keys or drives. USB3 drives are faster for backup etc. |
| Monitor | any |
| Graphics card | any supported |
4.2. Recommended Hardware Requirements
The following information is what we would suggest is the recommended minimum to utilize all the features of SME Server 10. How many users this configuration will support depends on how heavily the server will be utilized, but should be sufficient for at least 25 users.
| Category | Specifications |
|---|---|
| Architecture | PCIe-based x86-64 compatible processor |
| Processor speed | multi Core 2GHz |
| RAM | At least 4 GB for all services, 8 GB supports most likely applications, more will be utilised if available |
| Hard Drive | One or more SSD/NVMe/SATA/PATA or SCSI - at least 50 GB for the system, and more for the space needed by your data. Server-grade drives are strongly recommended for critical servers. |
| SCSI adapter | SCSI adapter must appear on the supported list (only necessary for SCSI systems) |
| Ethernet adapter(s) | The ethernet adapters installed on your server must appear on the supported list. |
| Modem (for dialup only) | Only modems that are Linux-compatible may be used. WinModems are not supported. |
| CD-ROM drive | SATA,ATAPI or SCSI - optional if installer is put on USB key |
| USB drive or key | USB2 is recommended for the install, as issues may arise with booting from USB3 keys or drives. USB3 drives are faster for backup etc. |
| Monitor | any |
| Graphics card | any supported |
4.3. Hard Drive Configuration
For default RAID configuration options as chosen by the installer, please see here: [RAID settings]
Do please note that the installer expects drives to be empty. Previously used drives should be wiped before being used for an install: this is sometimes tricky depending on which operating system was previously installed. Please see Here.
Do also note that selecting "Default Configuration" for storage from the text or GUI installer will override the SME defined automatic boot configuration for RAID! To recover from this a reboot will be necessary to reimplement the configuration before starting the installation.
4.4. Supported Ethernet or SCSI Adapters, or Tape Drives
Either one ethernet adapter (in the case of dialup connectivity or server-only mode) or two ethernet adapters (for dedicated connections in server and gateway mode) must be installed on your SME Server. Your ethernet adapters must be supported by Red Hat Enterprise Linux 7.
If the computer you plan to use for your server has a SCSI hard disk, your SCSI adapter must be supported by Red Hat Enterprise Linux 7.
If you intend to use the tape backup capabilities of the SME Server, you must have a tape drive that is supported by Red Hat Enterprise Linux 7.
4.5. Virtualisation requirements
- Virtualbox
- Proxmox
- Linux KVM
- VMWare
- etc.
You can virtualize the Koozali SME Server on any computer when your processor has amd-v or vtx instructions. You need these instructions to use more than one core in the virtualised guest. Note: sometimes although supported, this has to be enabled in the BIOS.
The amount of memory is a miminum of 2GB for the guest to be comfortable, and at least 4 GB with a lot of contribs installed; as always with memory more is usually better.
For more detailed information on a virtualized SME Server, please see the Virtual_SME_Server page.
