Difference between revisions of "Prosody"
m (→Installation: update version) |
|||
| (13 intermediate revisions by the same user not shown) | |||
| Line 7: | Line 7: | ||
These instructions are for SME Server '''9.0''' 64-bit only. | These instructions are for SME Server '''9.0''' 64-bit only. | ||
| − | Prosody is available from the [[epel|'''epel''']] repository, so you have to enable the [[epel|'''epel''']] repository. | + | Prosody (v0.9.12-1) is available from the [[epel|'''epel''']] repository, so you have to enable the [[epel|'''epel''']] repository. After enabling the [[epel|epel]] repository, prosody can be installed with: |
| − | After enabling the [[epel|epel]] repository, prosody can be installed with: | + | yum install prosody lua-ldap lua-event --enablerepo=epel |
| − | yum install prosody lua-ldap --enablerepo=epel | ||
| − | |||
==Configuration== | ==Configuration== | ||
| Line 16: | Line 14: | ||
To automatically start Prosody at boot and configure the ports: | To automatically start Prosody at boot and configure the ports: | ||
ln -s /etc/rc.d/init.d/e-smith-service /etc/rc7.d/S99prosody | ln -s /etc/rc.d/init.d/e-smith-service /etc/rc7.d/S99prosody | ||
| − | config set prosody service status enabled access private TCPPort 5222 | + | config set prosody service |
| − | You can toggle the access property to enable public/private access. | + | config setprop prosody status enabled |
| + | config setprop prosody access private | ||
| + | config setprop prosody TCPPort 5222 | ||
| + | config setprop prosody UDPPort 5222 | ||
| + | You can toggle the ''access'' property to enable public/private access. | ||
| + | |||
| + | |||
| + | |||
| + | Then to apply the new service: | ||
| + | signal-event remoteaccess-update | ||
| + | |||
===Configuration file=== | ===Configuration file=== | ||
Prosody's configuration file is located at: | Prosody's configuration file is located at: | ||
/etc/prosody/prosody.cfg.lua | /etc/prosody/prosody.cfg.lua | ||
| + | {{Note box|Please note that the latest version now has split configuration files. One for server wide settings and one for each virtual host. So the below example config file should be adjusted accordingly.}} | ||
| + | |||
The basic settings you have to change to run your prosody server on your domain (replace "example.com" with "yourdomain.com"): | The basic settings you have to change to run your prosody server on your domain (replace "example.com" with "yourdomain.com"): | ||
admins = {"admin@yourdomain.com"} | admins = {"admin@yourdomain.com"} | ||
| Line 42: | Line 52: | ||
TBA | TBA | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
==Documentation== | ==Documentation== | ||
Latest revision as of 09:04, 30 August 2017
About
"Prosody is a modern XMPP communication server (aka Jabber). It aims to be easy to set up and configure, and efficient with system resources. Additionally, for developers it aims to be easy to extend and give a flexible system on which to rapidly develop added functionality, or prototype new protocols."
Installation
These instructions are for SME Server 9.0 64-bit only.
Prosody (v0.9.12-1) is available from the epel repository, so you have to enable the epel repository. After enabling the epel repository, prosody can be installed with:
yum install prosody lua-ldap lua-event --enablerepo=epel
Configuration
Adding service and open ports
To automatically start Prosody at boot and configure the ports:
ln -s /etc/rc.d/init.d/e-smith-service /etc/rc7.d/S99prosody config set prosody service config setprop prosody status enabled config setprop prosody access private config setprop prosody TCPPort 5222 config setprop prosody UDPPort 5222
You can toggle the access property to enable public/private access.
Then to apply the new service:
signal-event remoteaccess-update
Configuration file
Prosody's configuration file is located at:
/etc/prosody/prosody.cfg.lua
The basic settings you have to change to run your prosody server on your domain (replace "example.com" with "yourdomain.com"):
admins = {"admin@yourdomain.com"}
allow_registration = true
VirtualHost "localhost"
VirtualHost "yourdomain.com"
enabled = true
You can now start prosody by entering:
service prosody start
Any XMPP client can register itself on your server or you can use LDAP authentication so that your SME Server users automatically have access to your XMPP server.
Register yourself as "admin" to be an administrator as defined in the configuration file.
Modules configuration
TBA
LDAP configuration
TBA
Documentation
For further and detailed configuration of the Prosody server and services, please see the Prosody documentation
