|
|
| (10 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| − | Please see my remarks at [[User_talk:Davidbray]] <small>— [[User:Cactus|Cactus]] ([[User talk:Cactus|talk]] | [[Special:Contributions/Cactus|contribs]]) </small> 16:48, 19 March 2010 (UTC)
| |
| | | | |
| − | Thanks Cactus - I've made some changes here so look forward to your feedback
| |
| − |
| |
| − | ===HowTo: Write the GRUB boot sector===
| |
| − | [[User:Trex|Trex]] ([[User talk:Trex|talk]]) 00:26, 5 February 2013 (MST) Should add a note as per the comment 24 in this Bug re grub will not install on an unpartioned disk
| |
| − |
| |
| − | [[User:Stephdl|Stephdl]] ([[User talk:Stephdl|talk]]) 12:24, 6 February 2013 (MST) ok i work on the howTo...work in progress, don't disturb :p
| |
| − |
| |
| − |
| |
| − |
| |
| − |
| |
| − | == HowTo: Remove a disk from the RAID1 Array from the command Line ==
| |
| − |
| |
| − | === Look at the mdstat ===
| |
| − |
| |
| − | First we must determine which drive is in default.
| |
| − |
| |
| − |
| |
| − | [root@sme8-64-dev ~]# cat /proc/mdstat
| |
| − | Personalities : [raid1]
| |
| − | md1 : active raid1 sdb1[1] sda1[0]
| |
| − | 104320 blocks [2/2] [UU]
| |
| − |
| |
| − | md2 : active raid1 sdb2[2](F) sda2[0]
| |
| − | 52323584 blocks [2/1] [U_]
| |
| − |
| |
| − | unused devices: <none>
| |
| − |
| |
| − | (S)= Spare
| |
| − | (F)= Fail
| |
| − | [0]= number of the disk
| |
| − |
| |
| − | {{note box|as we can see the partition sdb2 is in default, we can see the flag: sdb2 [2] (F)
| |
| − | we need to resynchronize the disk sdb to the existing raid md2.}}
| |
| − |
| |
| − | === Fail and remove the disk, '''sdb''' in this case ===
| |
| − |
| |
| − | [root@ ~]# '''mdadm --manage /dev/md2 --fail /dev/sdb2'''
| |
| − | mdadm: set /dev/sdb2 faulty in /dev/md2
| |
| − | [root@ ~]# '''mdadm --manage /dev/md2 --remove /dev/sdb2'''
| |
| − | mdadm: hot removed /dev/sdb2
| |
| − | [root@ ~]# '''mdadm --manage /dev/md1 --fail /dev/sdb1'''
| |
| − | mdadm: set /dev/sdb1 faulty in /dev/md1
| |
| − | [root@ ~]# '''mdadm --manage /dev/md1 --remove /dev/sdb1'''
| |
| − | mdadm: hot removed /dev/sdb1
| |
| − |
| |
| − | === Do your Disk Maintenance here ===
| |
| − |
| |
| − | At this point the disk is idle.
| |
| − |
| |
| − | [root@sme8-64-dev ~]# cat /proc/mdstat
| |
| − | Personalities : [raid1]
| |
| − | md1 : active raid1 sda1[0]
| |
| − | 104320 blocks [2/1] [U_]
| |
| − |
| |
| − | md2 : active raid1 sda2[0]
| |
| − | 52323584 blocks [2/1] [U_]
| |
| − |
| |
| − | unused devices: <none>
| |
| − |
| |
| − | {{note box|You'll have to determine if your disk can be reinstated at the array. In fact sometimes a raid can get out of sync after a power failure but also some outages times for physical disk itself. It is necessary to test the hard drive if this occurs repeatedly. For this we will use smartctl.}}
| |
| − |
| |
| − |
| |
| − |
| |
| − |
| |
| − | === Add the partitions back ===
| |
| − |
| |
| − | [root@ ~]# '''mdadm --manage /dev/md1 --add /dev/sdb1'''
| |
| − | mdadm: hot added /dev/sdb1
| |
| − | [root@ ~]# '''mdadm --manage /dev/md2 --add /dev/sdb2'''
| |
| − | mdadm: hot added /dev/sdb2
| |
| − |
| |
| − | === Another Look at the mdstat ===
| |
| − |
| |
| − | [root@ ~]# '''cat /proc/mdstat'''
| |
| − | Personalities : [raid1]
| |
| − | md2 : active raid1 sdb2[2] sda2[0]
| |
| − | 488279488 blocks [2/1] [U_]
| |
| − | [=>...................] recovery = 6.3% (31179264/488279488) finish=91.3min speed=83358K/sec
| |
| − | md1 : active raid1 sdb1[1] sda1[0]
| |
| − | 104320 blocks [2/2] [UU]
| |
| − |
| |
| − | unused devices: <none>
| |
