Difference between revisions of "Moving HardDisk to New Hardware"
| (7 intermediate revisions by 3 users not shown) | |||
| Line 3: | Line 3: | ||
This HowTo describes a simple way to move your SMEServer system to another set of hardware by just moving the hard disk. | This HowTo describes a simple way to move your SMEServer system to another set of hardware by just moving the hard disk. | ||
| − | + | <pre style="color:red"> | |
| + | Moving the HardDisk to new hardware usually works without any intervention, but sometimes the boot fails with a "Kernel Panic". | ||
| + | In this case you should follow these steps.</pre> | ||
| + | |||
| + | This technique seems to work for SME8, tested on SME8.0b7, no guarantees on any other version. | ||
===Backup First=== | ===Backup First=== | ||
| Line 23: | Line 27: | ||
chroot /mnt/sysimage | chroot /mnt/sysimage | ||
cd /boot | cd /boot | ||
| − | mv initrd | + | mv initrd-YOUR_KERNEL_VERSION.img initrd-YOUR KERNEL VERSION.img.old |
| − | mkinitrd initrd | + | mkinitrd initrd-YOUR_KERNEL_VERSION.img YOUR_KERNEL_VERSION |
*Then reboot and if it has worked, then the system will boot normally. | *Then reboot and if it has worked, then the system will boot normally. | ||
*If not, then you'll have to think again, or use the longer way as [[Moving_SME_to_new_Hardware|here]] or using a backup as [[http://wiki.contribs.org/Category:Backup Category:Backup]] | *If not, then you'll have to think again, or use the longer way as [[Moving_SME_to_new_Hardware|here]] or using a backup as [[http://wiki.contribs.org/Category:Backup Category:Backup]] | ||
| + | ==Acknowledgement== | ||
| + | |||
| + | This came about through a question I posted on the Forum, and was quickly answered by Stefano, many thanks to him. | ||
| − | [[Category:Howto]] [[Category: | + | http://forums.contribs.org/index.php/topic,48036.msg238015.html#msg238015 |
| + | [[Category:Howto]] [[Category:Administration:Storage]] | ||
Latest revision as of 16:02, 3 April 2017
Introduction
This HowTo describes a simple way to move your SMEServer system to another set of hardware by just moving the hard disk.
Moving the HardDisk to new hardware usually works without any intervention, but sometimes the boot fails with a "Kernel Panic". In this case you should follow these steps.
This technique seems to work for SME8, tested on SME8.0b7, no guarantees on any other version.
Backup First
Never do anything like this without a viable backup. If you have a Raid 1 system with 2 hard drives, then check you can boot from either of them, and then keep one safe in-case the procedure fails. If you have a USB hard Drive backup or some other form of backup, then I recommend you make sure it restores properly before you start.
What to Do
- Boot up the "old" system and run:
uname -r
this will give you the name of the current Kernel. It is needed below.
- Remove the hard Drive and load it into the new system
- Boot from an SMEServer ISO CD into rescue mode, by typing "sme rescue" at the initial prompt.
- Select to enter rescue mode in Read/Write mode
- Type in the following code:
chroot /mnt/sysimage cd /boot mv initrd-YOUR_KERNEL_VERSION.img initrd-YOUR KERNEL VERSION.img.old mkinitrd initrd-YOUR_KERNEL_VERSION.img YOUR_KERNEL_VERSION
- Then reboot and if it has worked, then the system will boot normally.
- If not, then you'll have to think again, or use the longer way as here or using a backup as [Category:Backup]
Acknowledgement
This came about through a question I posted on the Forum, and was quickly answered by Stefano, many thanks to him.
http://forums.contribs.org/index.php/topic,48036.msg238015.html#msg238015
