2,569
edits
Changes
Jump to navigation
Jump to search
Line 1:
Line 1: − If you have fixed a request make here can you remove the comments so we can see what is still to be done − Line 8:
Line 6: − :: Yes, I looked...+ − :: create a smeserver-sane with the templates: I don't have a lot of time at present+ − :: If I have a little of time...+ − :: I must finish the installation of mgetty / vgetty for SME before + − :: What Manufacturer and Model?+ − + − + − + − + − + − + − Hi Cactus, + − − I don't understand: − After succesfull of the required packages issue the following commands: − − signal-event post-upgrade − signal-event reboot − It isn't very good, it takes of 'CPU time ' − − Ecureuil − − − == Stick to SME Server default syntax and naming conventions please == − Thank you for providing this Howto I think a lot of users will like this in the future, but I modified your English version and I noticed you have changed some items back. IMHO you should not have done so as I made changes to make things more conform to the SME Server naming conventions and you should have adapted them in your other translation(s) as well. − A service normally is a daemon, hence the database record should be named saned (or sane) and not sane-port. On top of that I think it is also strange to call the group the server is configured to use to be saned, I therefore changed it to ''saneusers'' in the example to avoid confusion between users and the SANE daemon (which is normally referenced as saned).+ − - [[User:Cactus|Cactus]] 05:49, 4 April 2008 (MDT) − :: I don't speak english very good − :: Do not change anything without understanding and reading − :: View sane documentation: service = sane-port => grrrrrrrrrrrrrrr − :: http://www.sane-project.org/man/saned.8.html − :: http://penguin-breeder.org/sane/saned/ − :: thank you − :: − :: Another problem: − :: If xinetd start, ' saned - d128 ' will not be able to work − :: I prefer the French version for it. − :: − :: for signal-event post-upgrade and signal-event reboot: − :: The post upgrade and the reboot process are only needed for smeserver − :: packages using the template system. As sane-backend nor xinetd are − :: smeserver specific, we don't need these (expensive !) steps. − +
questions about 4300c
use templates not templates-custom
use templates not templates-custom
you just need to work out what needs to change
you just need to work out what needs to change
: Yes, I looked...
: create a smeserver-sane with the templates: I don't have a lot of time at present
: If I have a little of time...
: I must finish the installation of mgetty / vgetty for SME before
good work so far, I'm dusting off my old scanner...
good work so far, I'm dusting off my old scanner...
: What Manufacturer and Model?
:: sane-find-scanner
:: I do not have a lot of place on my server and Shad still did not recover my src rpm.
:: found USB scanner (vendor=0x03f0 [Hewlett-Packard], product=0x0305 [Hewlett-Packard ScanJet 4300C]) at libusb:002:003
:: Tomorrow I remove source of my server
:: and lsusb > Bus 002 Device 003: ID 03f0:0305 Hewlett-Packard ScanJet 4300c
:: [[User:Ecureuil|Ecureuil]]
:: but scanimage -L > No scanners were identified.
:: documentation suggest this may not be a problem if i can supply my device name
----
:: could you suggest what the syntax might be ?
:: http://www.sane-project.org/sane-mfgs.html#Z-HEWLETT-PACKARD > niash driver
:What do you mean by that I do not understand your remark. Above commands are normal (required) steps after installing software using yum on the SME Server shell. - [[User:Cactus|Cactus]] 05:41, 4 April 2008 (MDT)
: View sane documentation: service = sane-port => grrrrrrrrrrrrrrr
:: [[User:Ecureuil|Ecureuil]]
:: don't take offense, that is the nature of wiki, just make the change and if someone is wrong change it back with an explaination, which is what you do [[User:Snoble|Snoble]] 19:59, 4 April 2008 (MDT)