Difference between revisions of "Qpsmtpd check earlytalker"
(Remove {{Request_for_deletion}}) |
Unnilennium (talk | contribs) |
||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | {{Outdated|msg=this content is not relevant for SME9.2, SME10 and beyond : new plugin name earlytalker}} | ||
| + | |||
== qpsmtpd: check_earlytalker == | == qpsmtpd: check_earlytalker == | ||
When a remote mail server sends email to your SME server, the SMTP specifications stipulate that it must wait until your SME server says "go ahead" before transmitting anything. | When a remote mail server sends email to your SME server, the SMTP specifications stipulate that it must wait until your SME server says "go ahead" before transmitting anything. | ||
| Line 12: | Line 14: | ||
You can increase this default delay from 1 second (to 3 seconds in the following example) at present only with a custom template: | You can increase this default delay from 1 second (to 3 seconds in the following example) at present only with a custom template: | ||
| + | |||
| + | === Prior SME9.2 : check_earlytalker plugin=== | ||
mkdir -p /etc/e-smith/templates-custom/var/service/qpsmtpd/config/peers/0 | mkdir -p /etc/e-smith/templates-custom/var/service/qpsmtpd/config/peers/0 | ||
cd /etc/e-smith/templates-custom/var/service/qpsmtpd/config/peers/0 | cd /etc/e-smith/templates-custom/var/service/qpsmtpd/config/peers/0 | ||
echo "check_earlytalker wait 3" > 10check_earlytalker | echo "check_earlytalker wait 3" > 10check_earlytalker | ||
| + | signal-event email-update | ||
| + | === For SME9.2 and higher : earlytalker plugin === | ||
| + | |||
| + | if updating remove previous template custom: | ||
| + | rm /etc/e-smith/templates-custom/var/service/qpsmtpd/config/peers/0/10check_earlytalker | ||
| + | then install: | ||
| + | mkdir -p /etc/e-smith/templates-custom/var/service/qpsmtpd/config/peers/0 | ||
| + | cd /etc/e-smith/templates-custom/var/service/qpsmtpd/config/peers/0 | ||
| + | echo "earlytalker wait 3" > 10earlytalker | ||
signal-event email-update | signal-event email-update | ||
| − | The following command will let you monitor your connections to verify that | + | The following command will let you monitor your connections to verify that (check_)earlytalker is working as expected: |
| − | tail -f /var/log/qpsmtpd/current |tai64nlocal| egrep "Accepted connection| | + | tail -f /var/log/qpsmtpd/current |tai64nlocal| egrep "Accepted connection|earlytal" |
[[User:Mmccarn|Mmccarn]] 17:59, 9 October 2008 (UTC) | [[User:Mmccarn|Mmccarn]] 17:59, 9 October 2008 (UTC) | ||
[[Category: Howto]] | [[Category: Howto]] | ||
[[Category: Mail]] | [[Category: Mail]] | ||
Latest revision as of 14:58, 28 April 2024
qpsmtpd: check_earlytalker
When a remote mail server sends email to your SME server, the SMTP specifications stipulate that it must wait until your SME server says "go ahead" before transmitting anything.
The "go ahead" response on a SME server should look like
220 mail.mysmeserver.com ESMTP
Many spam servers do not wait for the "go ahead" from the receiving mail server. Waiting for each connection, even for as little as a second or two, would greatly increase the amount of time required to send the spam. Also, until recently most mail servers would accept the email even from impolite senders that didn't wait.
SME Server uses the qpsmtpd check_earlytalker plugin to reject email from any mail server that tries to send email without waiting for permission.
The default settings insert a 1 second delay after the remote system connects to the SME server before the SME server responds.
You can increase this default delay from 1 second (to 3 seconds in the following example) at present only with a custom template:
Prior SME9.2 : check_earlytalker plugin
mkdir -p /etc/e-smith/templates-custom/var/service/qpsmtpd/config/peers/0 cd /etc/e-smith/templates-custom/var/service/qpsmtpd/config/peers/0 echo "check_earlytalker wait 3" > 10check_earlytalker signal-event email-update
For SME9.2 and higher : earlytalker plugin
if updating remove previous template custom:
rm /etc/e-smith/templates-custom/var/service/qpsmtpd/config/peers/0/10check_earlytalker
then install:
mkdir -p /etc/e-smith/templates-custom/var/service/qpsmtpd/config/peers/0 cd /etc/e-smith/templates-custom/var/service/qpsmtpd/config/peers/0 echo "earlytalker wait 3" > 10earlytalker signal-event email-update
The following command will let you monitor your connections to verify that (check_)earlytalker is working as expected:
tail -f /var/log/qpsmtpd/current |tai64nlocal| egrep "Accepted connection|earlytal"
Mmccarn 17:59, 9 October 2008 (UTC)
