3,072
edits
Changes
From SME Server
Jump to navigationJump to searchno edit summary
Whenever a UPS event occurs Emails are sent to the admin account.
Whenever a UPS event occurs Emails are sent to the admin account.
</li></ol>
</li></ol>
====Configuring as a master====
edit the file /etc/ups/nut.conf, and modify the line
MODE=netserver
Set configuration values:
config setprop nut access private TCPPort 3493
expand-template /etc/ups/upsd.conf
expand-template /etc/rc.d/init.d/masq
systemctl restart masq
systemctl restart nut-server
====Configuring as a slave====
Set configuration values:
config setprop nut SlaveUPS UPS@192.168.33.11
config setprop nut Master no
Where 192.168.33.11 is your UPS master, that is the computer that is in direct communication with the UPS. The hostname of that computer may also work.
Apply changes and restart server:
signal-event post-upgrade
signal-event reboot
or (for SME10):
signal-event e-smith-nutUPS-update
Confirm server is communicating with master:
upsc UPS@192.168.33.11
====Connecting multiple UPS's====
To be added http://bugs.contribs.org/show_bug.cgi?id=629
<tabs container>
<tab name="SME 9">
{{Warning box|Be sure to have e-smith-nutUPS-2.4.0-9.el6.sme.noarch or higher to carry on with these instructions. If you get a lower version, just follow SME8 instruction.}}
rpm -qa e-smith-nutUPS
If you get NUT running with administrative privileges modification from sme8 instruction, you need to remove the custom template created for this. These variables are taken in charge by the new package.
First you need to delete the custom template file.( This command delete the directory, be sure you don't have personal file present. If the case, delete manualy the file created for administrative privileges )
rm -rf /etc/e-smith/templates-custom/etc/ups/upsd.users
Now, to get '''upsd''' to recognise the modification of user, we need to expand the template and reload the '''upsd''' configuration
/sbin/e-smith/expand-template /etc/ups/upsd.users
/usr/sbin/upsd -c reload
===Variables et commandes ASI===
Dans certains cas, vous souhaiterez peut-être modifier les variables de l'onduleur lui-même, telles que le paramètre Low Charge/LOWBATTERY. Cela nécessite l'utilisation de la commande '''upsrw''' et les privilèges d'administrateur ASI.
Vous souhaiterez peut-être également contrôler l'onduleur directement à partir de la ligne de commande en émettant des commandes ASI. Cela nécessite l'utilisation de la commande '''upscmd''' et les privilèges d'administrateur ASI.
{{Warning box|type=Attention : |en général, les données de l'onduleur doivent rester protégées et les modifications ou l'émission de commandes doivent être effectuées avec attention. Si vous souhaitez apporter des modifications aux données ou émettre des commandes, les privilèges d'administrateur peuvent être activés comme ci-dessous et doivent ensuite être désactivés.}}
====UPS Administrative Privileges====
You should check your new password ( AdminPass ) to run '''upserw''' & '''upscmd'''. Of course, you could change your password for a easier one to use.
config show nut
To set new admin password in database. The new password would be admin ( change it to suit your need )
config setprop nut AdminPass admin
To enabled administrative privileges and run command to ups.
config setprop nut AdminUser enabled
Now, to get '''upsd''' to recognise admin modification for administrative privileges we expand the template and reload the '''upsd''' configuration
/sbin/e-smith/expand-template /etc/ups/upsd.users
/usr/sbin/upsd -c reload
{{Note box|To disabled the administrative privileges once you have changed the UPS parameters or issued commands as required, issue the commands
config setprop nut AdminUser disabled
/sbin/e-smith/expand-template /etc/ups/upsd.users
/usr/sbin/upsd -c reload
}}
