Difference between revisions of "SANE"

yum --enablerepo=smecontribs install  smeserver-sane

expand-template /etc/xinetd.conf
expand-template /etc/services
expand-template /etc/hosts.allow
expand-template /etc/sane.d/saned.conf

service xinetd restart

signal-event post-upgrade; signal-event reboot

sane-find-scanner 

# No SCSI scanners found. If you expected something different, make sure that 
# you have loaded a SCSI driver for your SCSI adapter. 
# Also you need support for SCSI Generic (sg) in your operating system. 
# If using Linux, try "modprobe sg". 

found USB scanner (vendor=0x04b8 [EPSON], product=0x010f [EPSON Scanner 010F], chip=LM9832/3) at libusb:001:002 
# Your USB scanner was (probably) detected. It may or may not be supported by 
# SANE. Try scanimage -L and read the backend's manpage. 

# Not checking for parallel port scanners. 

# Most Scanners connected to the parallel port or other proprietary ports 
# can't be detected by this program. 

scanimage -L 

device `plustek:libusb:001:002' is a Epson Perfection 1250/Photo USB flatbed scanner 

scanimage -d drivername --format tiff -l 0 -t 0 -x 215 -y 297 > outfile.tiff 

scanimage -d plustek:libusb:001:002 --format tiff -l 0 -t 0 -x 215 -y 297 > outfile.tiff

rpm -e sane-backends sane-backends-libs  smeserver-sane

 nano -w /etc/sane.d/net.conf 

 IP_address_of_your_server 

/etc/init.d/xinetd stop
or
config setprop saned status disabled
/sbin/e-smith/expand-template /etc/xinetd.conf
/etc/init.d/xinetd restart 

saned -d128 

 # saned -d128 
 [saned] main: starting debug mode (level 128) 
 [saned] main: trying to get port for service `sane-port' (getaddrinfo)  
 [saned] main: [0] socket () using IPv4 
 [saned] main: [0] setsockopt () 
 [saned] main: [0] bind () to port 6566 
 [saned] main: [0] listen () 
 [saned] main: [1] socket () using IPv6 
 [saned] main: [1] socket failed: Address family not supported by protocol 
 [saned] main: waiting for control connection 

/etc/init.d/xinetd start
or
config setprop saned status enabled
/sbin/e-smith/expand-template /etc/xinetd.conf
/etc/init.d/xinetd restart

ID	Product	Version	Status	Summary (2 tasks) ⇒
4866	SME Contribs	7.4	CONFIRMED	smeserver-sane problem with specific scanner driver
4278	SME Contribs	7.3	CONFIRMED	scanner permissions

Difference between revisions of "SANE"

Latest revision as of 11:57, 9 August 2017

Contents

Information

Supported scanners

Server

Installation

SME 8.X, 9.X

Finish the installation

Testing the installation

Finding your scanner

Determining assigned driver

Aquisition

Uninstall

Client

Windows XP and Vista

Configuration

Usage

MacOS X

Linux

Configuration

Usage

Client Troubleshooting

Bugs

Navigation menu

Page actions

Page actions

Personal tools

Koozali SME Server

Recent activities

Koozali resources

Koozali SME Server wiki

Tools

Search

@@ Line 1: / Line 1: @@
 {{Languages|SANE}}
 ==Information==
+SANE stands for "Scanner Access Now Easy" and is an application programming interface (API) that provides standardized access to any raster image scanner hardware (flatbed scanner, hand-held scanner, video- and still-cameras, frame-grabbers, etc.)
+{{#smeversion:smeserver-sane}}
 For more information on SANE have a look at the [http://www.sane-project.org/ SANE project website]
 ===Supported scanners===
 For a list of supported scanners have a look at [http://www.sane-project.org/sane-supported-devices.html this page].
+Note the SME 8 rpm uses [http://www.sane-project.org/sane-backends-1.0.18.html this page]
+Note the SME 9 rpm uses [http://www.sane-project.org/sane-backends-1.0.21.html this page]
 ==Server==
 This is the installation of the server part, you will also need to install drivers on your clients as described in the [[#Client|Client]] section.
 ===Installation===
-====Installing required packages====
+==== SME 8.X, 9.X====
-To install SANE and xinetd (required for running it unattended) login to the SME Server shell as root and issue the following command:
- yum install sane-backends xinetd
-After succesfull of the required packages issue the following commands:
+Install SANE and required packages
-  signal-event post-upgrade
- signal-event reboot
+ yum --enablerepo=smecontribs install  smeserver-sane
+==== Finish the installation ====
+then
+ expand-template /etc/xinetd.conf
+ expand-template /etc/services
+ expand-template /etc/hosts.allow
+ expand-template /etc/sane.d/saned.conf
+ service xinetd restart
+or if you prefer to restart your server
+  signal-event post-upgrade; signal-event reboot
 ====Testing the installation====
@@ Line 56: / Line 77: @@
   scanimage -d plustek:libusb:001:002 --format tiff -l 0 -t 0 -x 215 -y 297 > outfile.tiff
-====Configuring xinetd to run SANE unattended====
-After succesfull installation and testing it is time to configure xinetd so SANE will run as a service on your server.
-<ol>
-<li>Create a group using the server-manager of your SME Server to hold the users that will be allowed to use the scanner application. In this instruction it is assumed that the group will be called saned.</li>
-<li>One of the first steps we need to do is to add a entry to the internal configuration database to hold the configuration parameters of the saned service daemon with the following commands:
-<pre>db configuration set sane-port service
-db configuration setprop sane-port TCPPort 6566
-db configuration setprop sane-port status enabled</pre>
-<!---db configuration setprop sane-port access private--->
-</li>
-<li>Create a custom template fragment by issuing the following commands:
-<pre>mkdir -p /etc/e-smith/templates-custom/etc/xinetd.conf/</pre>
-<pre>nano /etc/e-smith/templates-custom/etc/xinetd.conf/30sane</pre>
-Copy the following section in this file:
-<pre>
-{
-$OUT = <<HERE;
-service sane-port
-{
-port = 6566
-socket_type = stream
-protocol = tcp
-user = root
-group = saned
-wait = no
-server = /usr/sbin/saned
-}
-HERE
-}
-</pre>
-Expand the configuration file:
-<pre>expand-template /etc/xinetd.conf</pre>
-</li>
-<li>We also allow all systems on the network to be able to access the service, this is done by adding another template, with the following commands:
-<pre>mkdir -p /etc/e-smith/templates-custom/etc/hosts.allow
-nano /etc/e-smith/templates-custom/etc/hosts.allow/sane</pre>
-Copy the following section into the file:
-<pre>
-{
-    $DB->hosts_allow_spec('saned');
-}
-</pre>
-Expand the configuration file:
-<pre>expand-template /etc/hosts.allow</pre>
-</li>
-<li>
-Now we need to configure the service using the following commands:
-<pre>mkdir -p /etc/e-smith/templates-custom/etc/services/
-nano /etc/e-smith/templates-custom/etc/services/saned</pre>
-Add the following line to the file:
-<pre>sane-port      { ${'sane-port'}{TCPPort} }/tcp               # SANE network scanner daemon</pre>
-Expand the configuration file:
-<pre>expand-template /etc/services</pre>
-</li>
-<li>
-Now we need to configure saned.conf using the following commands:
-<pre>nano /etc/sane.d/saned.conf</pre>
-Add the following lines to the file:
-<pre>localhost
-adresse-ip_client1
-adresse_ip_client2</pre>
-</li>
-<li>Make a link to allow xinetd to start during the server startup:
-<pre>ln -s /etc/init.d/xinetd /etc/rc.d/rc7.d/S50xinetd</pre>
-</li>
-<li>Now we can start the server with the following command:
-<pre>/etc/init.d/xinetd restart</pre>
-</li>
-</ol>
 === Uninstall ===
 You can remove SANE from your SME Server with the following command
-  yum remove sane-backends
+  rpm -e sane-backends sane-backends-libs  smeserver-sane
-<!---
-====Determine scanner resolution====
- scanimage --help | grep -m 1 resolution
-=== Adding your scanner to the network ===
-saned is the SANE daemon. It gives an access to the image acquisition device available on the local host to remote clients.
-====Updating of /etc/hosts.allow for sane====
-Make in /etc/ hosts.allow a line with template-custom
- mkdir -p /etc/e-smith/templates-custom/etc/hosts.allow/
-  nano /etc/e-smith/templates-custom/etc/hosts.allow/saned
-  =>
-  saned: 127.0.0.1 10.97.1.0/255.255.255.0
-(10.97.1.0 => your ip)
-  /sbin/e-smith/expand-template /etc/hosts.allow
-====Updating of /etc/services for sane====
-Make in /etc/services a line with template-custom
-  mkdir -p /etc/e-smith/templates-custom/etc/services/
-  nano /etc/e-smith/templates-custom/etc/services/saned
-  =>
-  sane 6566/tcp # SANE network scanner daemon
-  expand-template /etc/services
-====Add the IP addresses of the computers which are authorized to use the scanner====
-  nano /etc/sane.d/saned.conf
-  =>
-  localhost
-  adress-ip_customer1
-  adress_ip_customer2
---->
 ==Client==
@@ Line 187: / Line 88: @@
 http://sanetwain.ozuzo.net/
-In download section, take  the ZIPfile (sanetwain127.zip or Windowsinstaller (setup127.exe)
+In download section, take the ZIP file (sanetwain127.zip and Windowsinstaller (setup127.exe)
-make :
-  setup127.exe
 ====Configuration====
 - index connection
-Hostname  => address ip server
+:Hostname  => address ip server
-Port => 6566
+:Port => 6566
-Username => user’s name
+:Username => user’s name
 I made : Get list of devices on startup
 - index printer
-I made : Show printer setup dialog before print
+:I made : Show printer setup dialog before print
-(I have several printers!)
+:(I have several printers!)
 - index Startup
-I made : Acquire preview on program start
+:I made : Acquire preview on program start
-Use as interface language => fr
+:Use as interface language => fr
+====Usage====
+SANE TWAIN drivers have many possibilities. SANE TWAIN drivers can be used alone or called from another application (photoshop, acrobat, ...) like a classical usb scanner.
+===MacOS X===
+SANE can also be installed on MacOS X, for more information have a look at
+http://www.ellert.se/twain-sane/.
+If you get things working on MacOS X please provide installation instructions here.
+===Linux===
+To use SANE on your linux PC you need to install the xsane package.
+====Configuration====
+Then configure xsane so that it knows where to find the server with the scanner attached, add a line with the IP address of your server to /etc/sane.d/net.conf on your client PC
+  nano -w /etc/sane.d/net.conf
+  IP_address_of_your_server
 ====Usage====
-SANE TWAIN drivers have many possibilities. SANE TWAIN drivers can be used alone or called from another application (photoshop, acrobat, ...) like a classical usb scanner.
+You can use kooka or xsane or make the acquisition from other software for instance OpenOffice or GIMP.
+===Client Troubleshooting===
+{{Incomplete}}
+Only needed if your client can't find the scanner
-====Testing====
+Disable saned
+ /etc/init.d/xinetd stop
+ or
+ config setprop saned status disabled
+ /sbin/e-smith/expand-template /etc/xinetd.conf
+ /etc/init.d/xinetd restart
-Start a terminal on your server (with putty for example).
+Start a terminal on your server.
-make :
+ saned -d128
-  saned -d128
 example
    # saned -d128
    [saned] main: starting debug mode (level 128)
    [saned] main: trying to get port for service `sane-port' (getaddrinfo)
-  [saned] main: "sane-port" service unknown on your host; you should add
-  [saned] main: sane-port 6566/tcp saned # SANE network scanner daemon
-  [saned] main: to your /etc/services file (or equivalent). Proceeding anyway.
    [saned] main: [0] socket () using IPv4
    [saned] main: [0] setsockopt ()
@@ Line 234: / Line 156: @@
    [saned] main: waiting for control connection
-If you have “waiting for control connection “, all sounds good. Now on your windows computer, open Scanimage (name of gui software for sanetwain)
+If you have “waiting for control connection “, all sounds good. Now on your scanning software, eg Scanimage (name of gui software for sanetwain)
-The scanner should start and lines should appear in the terminal (putty)
+The scanner should start and lines should appear in the terminal.
 On the first connection, it often takes a long time and a message like this can appear: Time out reading word from socket
@@ Line 252: / Line 174: @@
 I put in comment (# in front of the line) all lines which did not correspond to my driver.
-===MacOS X===
+Enable saned when finished
-{{Incomplete}}
+ /etc/init.d/xinetd start
-SANE can also be installed on MacOS X, for more information have a look at
+ or
-http://www.ellert.se/twain-sane/.
+ config setprop saned status enabled
+ /sbin/e-smith/expand-template /etc/xinetd.conf
-If you get things working on MacOS X please provide installation instructions here.
+ /etc/init.d/xinetd restart
+=== Bugs ===
-===Linux===
+Please raise bugs under the SME-Contribs section in {{BugzillaFileBug|product=|component=|title=bugzilla}}and select the smeserver-sane component or use {{BugzillaFileBug|product=SME%20Contribs|component=smeserver-sane|title=this link}}.
-To use SANE on your linux PC you need to install the xsane package.
+{{#bugzilla:columns=id,product,version,status,summary |sort=id |order=desc |component=smeserver-sane |noresultsmessage="No open bugs found."}}
-It’s enough to configure xsane so that it knows where to find the server with the scanner attached by adding the line with the IP address of your server to /etc/sane.d/net.conf on your client PC
-You can use xsane or make the acquisition from other software for instance OpenOffice or GIMP.
 ----
-[[Category:Howto]]
+[[Category:Contrib]]
+[[Category:Administration]]

	Incomplete:
	This article or section needs to be expanded. Please help to fill the gaps or discuss the issue on the talk page